Autonomous photovoltaic system for refrigerator 12V / 65watt - 75 watts
Autonomous photovoltaic kit / package for small refrigerator 65-75 watt / 12V or 220V by adding inverter
Victron BlueSolar PWM Charge Controller-LCD and USB 12 / 24V / 20A 20A charge regulator
42.00 € Excluding VAT
52.08 € Includes VAT
Victron BlueSolar PWM Charge Controller-LCD and USB 12 / 24V / 20A Solar Charge Controller 20A Digital with Liquid Crystal Display for Photovoltaic Panels
Available on backorder
... people are viewing this right now
Victron BlueSolar PWM Charge Controller-LCD and USB 12 / 24V / 20A Solar Charge Controller 20A Digital with Liquid Crystal Display for Photovoltaic Panels
Victron BlueSolar PWM Charge
Liquid crystal display
For status monitoring and adjustment
Output loading
Battery overload can be avoided by connecting all loads to the load output. The load output will disconnect the load when the battery is discharged to a predetermined voltage. Some loads (especially inverters) can best be connected directly to the battery and the inverter remote control connected to the load output. You may need a special interface cable, refer to the manual. The connection and disconnection voltages are adjustable.
Day / night timing of cargo output
This option allows a preset ON-time after dusk.
Programmable battery charging algorithm
Programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (only with internal BMS)
Two 5 Volt USB outputs
Maximum current (both outputs combined): 2A
(VIC-BlueSolar_PWM-LCD-USB)
• Low cost PWM controller
• Internal heat sensor
• Three stages of battery charging (total, absorption, suspension)
• It is protected against overvoltage
• It is protected against a short circuit
• It is protected from reverse polar connection of photovoltaic panels.
• Disconnects the output with low voltage
• Optional remote view (20A model only)
Victron BlueSolar PWM Charge Controller-LCD and USB 12 / 24V / 20A Solar charge regulator 20A
BlueSolar PWM Charge
• PWM controller
• Programmable charging current ratio (normal setting: equal current for both batteries)
• Charging voltage regulation of three types of batteries (Gel, AGM and Flooded)
• Internal heat sensor and optional remote control heat sensor
• It is protected against overvoltage
• It is protected against a short circuit
• It is protected from reverse polarity of photovoltaic panels and / or batteries.
BlueSolar 12 / 24-20 with timer 20A to 12V or 24V
• PWM photovoltaic lighting controller.
• The two timers allow operation from night time until sunrise or for a limited time after night and for a limited time before nightfall.
• Seven sections display the timer settings and analyze fault conditions.
• Battery status indicator with excessive battery discharge warning signal.
• Internal heat sensor.
• Three stages of battery charging (total, absorption, suspension).
• It is protected against overvoltage.
• It is protected against a short circuit.
• It is protected from reverse polarity of photovoltaic panels and / or batteries.
• With low voltage disconnects the device for bypass.
models: 12/24/48 Volt
Information about him Victron BlueSolar PWM Charge Controller-LCD and USB 12 / 24V / 20A
Price without VAT
| Weight | 1 kg |
|---|---|
| Brand |
Related products
Victron BlueSolar PWM Light 48V / 10A - PWM 10A Charging Regulator for Photovoltaics
63.00 €
49.00 € Excluding VAT
60.76 € Includes VAT
49.00 € Excluding VAT
60.76 € Includes VAT
Victron BlueSolar PWM Light 48V / 10A - PWM 10A Charging Regulator for Photovoltaics
Its charge regulator Victron Bluesolar PWM Light 48V-10A is compatible with European standards EN60335-1, EMC EN61000-6-1, EN61000-6-3. You do not want to be frustrated if you cannot get the right pitch so invest in a good capo that will extend your life for a while.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 48V |
| Permitted Humidity | max. 95% RF (not condensing) |
| IP Protection | IP20 |
| Charging Current max. | 10A |
| Standby Self-Consumption | 10mA |
| Max. Voltage Solar Module | 100V |
| Max. Current Solar Module | 10A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Available on backorder
Cotek CX2425 Battery Charger - 24V - 25A - 230VAC
349.00 €
279.00 € Excluding VAT
345.96 € Includes VAT
279.00 € Excluding VAT
345.96 € Includes VAT
Cotek CX2425 Battery Charger - 24V - 25A - 230VAC
Price without VAT
In stock
CHARGING REGULATOR PHOCOS CX-40 12 / 24V - 40A
97.30 €
67.00 € Excluding VAT
83.08 € Includes VAT
67.00 € Excluding VAT
83.08 € Includes VAT
System voltage: 12V / 24V automatic selection. Maximum charging / load current: 40A / 40A Same consumption: operating temperature: -20 ~ + 50⁰C Dimensions: 92 x 93 x 38 mm Weight: 168gr Protection: IP22
Price without VAT
Out of stock
Victron BlueSolar PWM PRO 10A
29.00 €
25.00 € Excluding VAT
31.00 € Includes VAT
25.00 € Excluding VAT
31.00 € Includes VAT
Victron BlueSolar PWM PRO 12 / 24V-10A - PWM Charging Regulator (12 / 24V) 10A for Photovoltaics
The BlueSolar PWM-Pro series is ready to use with the default settings. It has three stages of battery charging (Bulk, absortion, float), protection against short circuit and over-voltages as well as from reverse polarity of the solar panels and / or the battery. These unique features make the BlueSolar PWM -Pro 12 / 24V-10A controller one of the most valuable controllers on the market. It can also be programmed easily, quickly and correctly with the help of the integrated BlueSolar Pro remote control panel.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 12V, 24V |
| Connectivity | Fananzeige Pro Fanbedienpanel, PWM-Pro with USB Interface Cable, Temperature Turbines |
| Permitted Humidity | max. 98% (not condensing) |
| IP Protection | IP30 |
| Charging Current max. | 10A |
| Standby Self-Consumption | 10mA |
| Max. Voltage Solar Module | 28V / 55V |
| Max. Current Solar Module | 10A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Price without VAT
Available on backorder
Charging regulator VS6024BN 60A PWM-USB
129.00 €
119.00 € Excluding VAT
147.56 € Includes VAT
119.00 € Excluding VAT
147.56 € Includes VAT
Charging regulator VS6024BN 60A PWM with programmable screen
Suitable for charging the batteries with current up to 60A (ie with photovoltaic panels with a total power of 1.500Wp at 24V or 750Wp at 12V). It also has a socket for connecting devices, with their automatic shutdown before the battery is completely discharged, thus protecting it from premature wear. The regulator stops charging automatically when the batteries charge.
It has digital screen with indications of the charging status and voltage of the batteries or the output of the panels in Ampere and the possibility of adjusting the charging voltage of the batteries. Shows the battery charge rate, what is the operating voltage while fully programmed.
Price without VAT
Out of stock
Victron BlueSolar PWM PRO 12 / 24V-20A - PWM Charging Regulator (12 / 24V) 20A for Photovoltaics
51.00 €
43.00 € Excluding VAT
53.32 € Includes VAT
43.00 € Excluding VAT
53.32 € Includes VAT
Victron BlueSolar PWM PRO 12 / 24V-20A - PWM Charging Regulator (12 / 24V) 20A for Photovoltaics
The BlueSolar PWM-Pro series with default operating settings is one of the most advantageous and reliable solutions on the market. The charge regulator BlueSolar PWM-Pro 12 / 24V-20A has three battery charging stages (Bulk, absortion, float) which maximizes the battery life and the smooth operation of your photovoltaic system. It also has protection against short circuits and overvoltages as well as from reverse polarity phenomena of solar panels or the battery. It can also be programmed with the help of the integrated BlueSolar Pro remote control panel easily, quickly and correctly.
Programmable with night mode
- The BlueSolar PWM-Pro 12 / 24V-20A charge controller is ready to use with its default settings. It is also fully programmable with the help of the BlueSolar Pro Remote Panel
- Three stages of battery charging (programmed with the help of BlueSolar Pro Remote Panel)
- Battery status check function (Remote Panel required)
- Night mode (Remote Panel required)
- Load output with battery discharge protection, overload protection and short circuit.
- Reverse polarity protection of photovoltaic - battery.
- Optional external temperature sensor.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 12V, 24V |
| Connectivity | Fananzeige Pro Fanbedienpanel, PWM-Pro with USB Interface Cable, Temperature Turbines |
| Permitted Humidity | max. 98% (not condensing) |
| IP Protection | IP30 |
| Charging Current max. | 20A |
| Standby Self-Consumption | 10mA |
| Max. Voltage Solar Module | 28V / 55V |
| Max. Current Solar Module | 20A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Available on backorder
Cotek CX1280 Battery Charger - 12V - 80A - 230VAC
679.00 €
499.00 € Excluding VAT
618.76 € Includes VAT
499.00 € Excluding VAT
618.76 € Includes VAT
Cotek CX1280 Battery Charger - 12V - 80A - 230VAC
Price without VAT
In stock
Victron BlueSolar PWM PRO 12 / 24V-5A - PWM Charging Regulator (12 / 24V) 5A for Photovoltaics
26.00 €
22.00 € Excluding VAT
27.28 € Includes VAT
22.00 € Excluding VAT
27.28 € Includes VAT
Victron BlueSolar PWM PRO 12 / 24-5A - PWM Charging Regulator (12 / 24V) 5A for Photovoltaics
The BlueSolar PWM-Pro series is ready to use with the default settings. It has three stages of battery charging (Bulk, abortion, float), protection against short circuit and over-voltages as well as from reverse polarity of the solar panels and / or the battery. In this way your battery is charged in the best way resulting in its much longer life while ensuring the smooth operation of your photovoltaic system. Also the charge regulator BlueSolar PWM-Pro 12 / 24V-5A Victron can be programmed with the help of the integrated BlueSolar Pro remote control panel making it one of the best choices on the market.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 12V |
| Permitted Humidity | max. 95% RF (not condensing) |
| IP Protection | IP20 |
| Charging Current max. | 5A |
| Standby Self-Consumption | 10mA |
| Battery Voltage | 12V, 24V |
| Load Current max. | 5A |
| Max. Voltage Solar Module | 28V / 55V |
| Max. Current Solar Module | 5A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Available on backorder
LS2024EU 20A PWM-USB Charging regulator
28.00 €
14.50 € Excluding VAT
17.98 € Includes VAT
14.50 € Excluding VAT
17.98 € Includes VAT
LS2024EU 20A PWM charge controller with USB
Ο charge regulator LS2024EU 20A with USB output provides efficient charging by applying the new PWM technology, increasing the battery life and improving the performance of the photovoltaic panels of a system; Load output · Provides battery temperature compensation ensuring proper charging and discharging of parameters automatically.
Features Electronic protection: · Load overload protection · Short circuit protection · Over-discharge battery protection · Reverse battery polarity protection
Price without VAT
Out of stock
Hybrid Controller 600W
199.00 €
149.00 € Excluding VAT
184.76 € Includes VAT
149.00 € Excluding VAT
184.76 € Includes VAT
Hybrid controller SAC SSWC-06-1224 with Digital Display
PMW technology,
Reinforced circuit.
12V / 24V operation. Automatic Identification System.
Price without VAT
Out of stock
CHARGING REGULATOR PHOCOS CX-2048 24 / 48V - 20A
119.16 €
99.00 € Excluding VAT
122.76 € Includes VAT
99.00 € Excluding VAT
122.76 € Includes VAT
Use in small autonomous and large photovoltaic installations. The charge regulator for photovoltaics CX20-48 has an LCD graphic display, which displays the charge status of the battery and the charge, as well as the operation of the photovoltaics.
Price without VAT
In stock
10A PWM charge regulator LS1024
19.00 €
11.50 € Excluding VAT
14.26 € Includes VAT
11.50 € Excluding VAT
14.26 € Includes VAT
10A, programmable charge regulator with night mode.
Technical data - programming
| QUICK START INSTRUCTIONS | |||||||||||||||||||||||||||||||||||
| This section provides a brief overview of how to get started using the controller. However, please review the entire manual to ensure best performance and years of trouble-free service. 1. Mount the controller on a vertical surface. Allow space above and below the controller for air flow. 2. Make sure the PV and load currents will not exceed the ratings of the controller being installed. 3. It is recommended that the connections be made in order from 1 to 6. (see the following picture) |
|||||||||||||||||||||||||||||||||||
| 4. Connect the BATTERY first. Use care that bare wires do not touch the metal case of the controller. 5. Connect the SOLAR (PV array) next. The green LED indicator will light if sunlight is present. 6. Connect the LIGHT last. If the red LED indicator lights, the battery capacity is low and should be charged before completing the system installation 7. Press the BUTTON as 6 or 7 to verify the system connection. |
|||||||||||||||||||||||||||||||||||
| 3. Connect the consumer to the charge regulator - plus and minus Please observe that the automatic adjustment to 12V / 24V systems does not function properly, if this sequence order is not followed. An improper sequence order can damage the battery! | |||||||||||||||||||||||||||||||||||
| LIGHTING CONTROL OPTIONS | |||||||||||||||||||||||||||||||||||
| 1. Press the power switch for 5 seconds, and select the desired LIGHTING CONTROL option. The LED is on, which confirms you have selected the right one. 2. The controller requires 10 minutes of continuous transition values before it starts to work. These constraints avoid false transitions due to lightning or dark storm clouds. 3. 10 minutes off before the controller starts to work. 4. A brief description follows below: |
|||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||
Price without VAT
Out of stock
Most viewed products
-
10kW PPC Photovoltaic ECO 545 Solar on roofs
6,800.00 €
5,300.00 € Excluding VAT
6,572.00 € Includes VAT10 Kwatt photovoltaic on roofs with interconnected to PPC photovoltaic system with installation
Photovoltaic Eco 545
See all offers here
Available on backorder
-
5kW PPC Photovoltaic ECO Solar 410-420 WATT with possibility for Installation
7,280.00 €
4,800.00 € Excluding VAT
5,952.00 € Includes VAT
410-WATT-420-WATT-
About answers to the most common questions about photovoltaics in homes. See the special offers of photovoltaics for 2022
5kw with photovoltaics on roofs with photovoltaics and installation Additional offers here
Available on backorder
-
Net metering 5kW photovoltaic package with 450 watt panels
3,650.00 €
2,750.00 € Excluding VAT
3,410.00 € Includes VATNet metering 5kW photovoltaic package offer
11 Photovoltaic panels 450 watts
Network inverter Renac NA 5000 DS (7500WATT max) 10 Year Warranty
Tile roof supports for 11 PV panels.
In stock
-
Autonomous photovoltaic package 1.2kWh/24 hours-12v
599.00 €
465.00 € Excluding VAT
576.60 € Includes VATAvailable on backorder
-
Net metering 10kW energy offset with PPC
6,700.00 €
5,590.00 € Excluding VAT
6,931.60 € Includes VATNet metering 10kW for energy offset and savings with PPC with production up to 16.600kWh per year
Available on backorder
-
Autonomous PV for a holiday home 4,5kWh with air conditioner
2,600.00 €
1,780.00 € Excluding VAT
2,207.20 € Includes VATAutonomous photovoltaic for a 4,5kWh cottage with air conditioning
Available on backorder
-
Net-metering 10kw with 10kwh lithium battery for storage with 460 WATT PV and Panels Complete package
17,800.00 €
14,100.00 € Excluding VAT
17,484.00 € Includes VATNet-metering 10kw with 10kwh lithium battery for storage with PV 460 WATT and Panels Complete AC/DC package for energy compensation (10 year inverter warranty)
Net metering 10kw with 10kwh lithium battery ( They produce in the summer in southern areas 40-50kw daily and about half or 1/3 in Winter) 12.000 - 16.000 kw averaged per year in Southern regions.
Price without VAT
Available on backorder
-
Photovoltaic Luxor 540 watt mono half cell ecoline LX-540M / 182-144-Germany
329.00 €
159.00 € Excluding VAT
197.16 € Includes VAT565 watts now available
LUXOR 565W N-Type TopCon LX-565TC M/144/N-TYPE/FS35/SW/16B/1500V Dimensions 2279x1134x35. Information here
Suitable for net-metering, home photovoltaics, parks and photovoltaic stations
Minimum purchase quantity 9 pieces
Out of stock
-
5 kwh- 7kwh/24v/220AC – 24V Premium Photovoltaic System
3,750.00 €
2,950.00 € Excluding VAT
3,658.00 € Includes VAT4 pcs. Φ / Β panel Solar Energy SE 270 / 270-275 watt Poly/ European. They have positive Photovoltaic system Premium 24V tolerance and power in watts. That is, they always deliver more watts than their rated power, high efficiency installed power 1080 watts up to + 5% more efficiency. Available with 12 years warranty factory equipment and 25 years warranty 80% yield.
1 pc. pure sine wave inverter Phoenix 24/1600 3200 watt power supply high reliability. Suitable for operation of all devices of corresponding power. Provides energy savings of up to 25% on self-consumption due to stabilized sine. Warranty 60 months (5 years)
4 pcs. Batteries S. Energy ECOAGM 220 / 250AH C100 type VRLA/ AGM corresponding specifications to GEL batteries. (deep closed type discharge lasting 10-12 years of life). Total 828AH / 12V
Possibility to add 2V High-strength and longer-lasting batteries in extreme uses at a small additional cost.
1 pc. Charging regulator Phocos CXN 40 (Digital programmable) (2 years warranty)
Ability to add MPPT controller with datalogger to increase efficiency up to 25% at a small additional cost.
Available on backorder
-
Autonomous photovoltaic for caravans or cottages 0,5kWh
630.00 €
495.00 € Excluding VAT
613.80 € Includes VATAvailable on backorder
Recently viewed products
-
Xantrex SW 4548 E
5,096.00 €
3,545.00 € Excluding VAT
4,395.80 € Includes VATConverter 4500 VA 48V with integrated charger and metal relay.
Price without VAT
-
Pure Sine Inverter Premium SK - 1000-S-TY-24V
329.00 €
279.00 € Excluding VAT
345.96 € Includes VATProduct Name: Premium SK - 1000-S-TY-24V
Voltage: 24V
Series: Premium S with built-in digital display
Powerful and reliable Inverter pure sine Premium SK - 1000-S-TY-24V from high-efficiency Solar Energy with energy savings in relation to the self-consumption of powered appliances up to 25%. The pure sine wave converter provides an output voltage waveform that has very low harmonic distortion. Suitable for all devices with this voltage and operating frequency. It also supports devices that have a high current requirement when starting. The product complies with the standards of quality, safety and good operation of European markets - German technology.
Use: caravans, yachts, boats, photovoltaic systems, hybrid systems, caravans, compressors, air conditioners, engines, pumps, remote storage, household electrical appliances, office electrical appliances, computers, laptops, mobile phone chargers, etc. Inverters of this type can also prevent computer errors, noise and malfunctions on screens, TVs, game consoles, etc. At the same time they are a reliable source of power for all your electronic devices.
Product Warranty: 30 Months
In stock
-
Victron Phoenix 12/1200 Schuko outlet * - Pure Sine Inverter with Power 1200 VA for Photovoltaics
425.00 €
300.00 € Excluding VAT
372.00 € Includes VATVictron Phoenix 12/1200 Schuko outlet * - Pure Sine Inverter 12V / 1200VA / 230V for Photovoltaics
The small series of Victron inverters continues to use the proven solution of the complete bridge with a toroidal transformer. The new series, however, has a new casing, new electronics and new software.
The units consist of a steel frame with a plastic cover, while the electronic management of the inverters provides improved dynamic stability of the output voltage. Last but not least is the range of communication and feature configuration options offered by Victron using VE.Direct software.
Technical Characteristics
Power : 1200 VA
Input voltage: 12 V DC
Output voltage: 230 V AC
Έξοδος: SHUKO
Peak power: 2400 W
Performance level : 94%
Available on backorder
-
Blue Power IP67 Charger 24/8 Battery Charger (1 'Output + Si)
174.00 €
147.00 € Excluding VAT
182.28 € Includes VATCharger Blue Power IP 67 fully protected: waterproof, with protection against vibration and ignition
The Blue Power IP67 charger is not at risk from water, oil or dirt. The housing is made of cast aluminum and the electronic components are made of resin molds.Price without VAT -
Fronius PRIMO GEN24 5.0 PLUS mains inverter for photovoltaics
2,421.00 €
1,890.00 € Excluding VAT
2,343.60 € Includes VATFronius PRIMO GEN24 5.0 PLUS mains inverter for photovoltaics. Suitable inverter for net metering, photovoltaic on roofs, home and professional photovoltaic systems.
-
Network Inverter SUNG SG5.0RT
1,504.00 €
1,211.00 € Excluding VAT
1,501.64 € Includes VATNetwork Inverter SUNG SG5.0RT Three-phase converter
Available on backorder
-
Rolls 12 EHG 210p
1,032.00 €
789.00 € Excluding VAT
978.36 € Includes VAT210AH 12V 7 year warranty
Series 4000 - 12Volt (6 Components) double container
SERIES 4000 MARINE / 7 YEARS WARRANTY Price without VAT
Out of stock
-
Economical autonomous Photovoltaic 3.5kwh-4.5kwh
1,695.00 €
1,299.00 € Excluding VAT
1,610.76 € Includes VATEconomical autonomous photovoltaic 3.5kwh-4.5kw
Available on backorder
-
6 PzS 930PB 2V Deep discharge SUNLIGHT battery
184.00 €
178.50 € Excluding VAT
221.34 € Includes VAT6 PzS 930PB 2V Deep discharge SUNLIGHT battery. Traction battery - open type with liquids, 930Ah (C5), with 2500 cycles at 50% DOD and with excellent performance in applications that require deep discharge. Suitable for electric lifting machines - clark - clark, service on boats, autonomous photovoltaic systems and generally electric applications. SUNLIGHT traction batteries optimize your business, as they provide reliable daily energy to your industrial or commercial vehicles.
Specifications
Electrical voltage 2 Capacity (C5) 775 [AH] Length 198 [mm] Width 119 [mm] Height 713 [mm] Height with poles 740 [mm] Weight 50.500 [kg] Ind NO Applications
In stock
-
3 PzS 345PB 2V Deep discharge SUNLIGHT battery
85.00 €
79.40 € Excluding VAT
98.46 € Includes VAT3 PzS 345PB 2V Deep discharge SUNLIGHT battery. Traction battery - open type with liquids, 345Ah (C5), with 2500 cycles at 50% DOD and with excellent performance in applications that require deep discharge. Suitable for electric lifting machines - clark - clark, service on boats, autonomous photovoltaic systems and generally electric applications. SUNLIGHT traction batteries optimize your business, as they provide reliable daily energy to your industrial or commercial vehicles.
Specifications
Electrical voltage 2 Capacity (C5) 345 [AH] Length 198 [mm] Width 65 [mm] Height 548 [mm] Height with poles 575 [mm] Weight 20.000 [kg] Ind NO In stock
