Autonomous photovoltaic system for refrigerator 12V / 65watt - 75 watts
Autonomous photovoltaic kit / package for small refrigerator 65-75 watt / 12V or 220V by adding inverter
- Quantity of product 430 watt Photovoltaic Luxor LX-430M/108 N-Type TopCon MBB (Mono)-Germany can not be less than 12
Victron BlueSolar PWM Charge Controller-LCD and USB 12 / 24V / 10A 10A charge regulator
34.50 € Excluding VAT
42.78 € Includes VAT
Victron BlueSolar PWM Charge Controller-LCD and USB 12 / 24V / 10A Solar Charge Controller 10A Digital with Liquid Crystal Display for Photovoltaic Panels
Available on backorder
... people are viewing this right now
Victron BlueSolar PWM Charge Controller-LCD and USB 12 / 24V / 10A Solar Charge Controller 10A Digital with Liquid Crystal Display for Photovoltaic Panels
Controller-LCD and USB Liquid crystal display
For status monitoring and adjustment
Output loading
Battery overload can be avoided by connecting all loads to the load output. The load output will disconnect the load when the battery is discharged to a predetermined voltage. Some loads (especially inverters) can best be connected directly to the battery and the inverter remote control connected to the load output. You may need a special interface cable, refer to the manual. The connection and disconnection voltages are adjustable.
Day / night timing of cargo output
This option allows a preset ON-time after dusk.
Programmable battery charging algorithm
Programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (only with internal BMS)
Two 5 Volt USB outputs
Maximum current (both outputs combined): 2A
(VIC-BlueSolar_PWM-LCD-USB)
• Low cost PWM controller
• Internal heat sensor
• Three stages of battery charging (total, absorption, suspension)
• It is protected against overvoltage
• It is protected against a short circuit
• It is protected from reverse polar connection of photovoltaic panels.
• Disconnects the output with low voltage
• Optional remote view (20A model only)
Victron BlueSolar PWM Charge Controller-LCD and USB 12/24V/10A Solar Charge Controller 10A
• PWM controller
• Programmable charging current ratio (normal setting: equal current for both batteries)
• Charging voltage regulation of three types of batteries (Gel, AGM and Flooded)
• Internal heat sensor and optional remote control heat sensor
• It is protected against overvoltage
• It is protected against a short circuit
• It is protected from reverse polarity of photovoltaic panels and / or batteries.
BlueSolar 12 / 24-10 with timer 10A to 12V or 24V
• PWM photovoltaic lighting controller.
• The two timers allow operation from night time until sunrise or for a limited time after night and for a limited time before nightfall.
• Seven sections display the timer settings and analyze fault conditions.
• Battery status indicator with excessive battery discharge warning signal.
• Internal heat sensor.
• Three stages of battery charging (total, absorption, suspension).
• It is protected against overvoltage.
• It is protected against a short circuit.
• It is protected from reverse polarity of photovoltaic panels and / or batteries.
• With low voltage disconnects the device for bypass.
models: 12/24/48 Volt
Victron BlueSolar PWM Charge Controller-LCD and USB 12 / 24V / 10A Solar charge regulator 10A
Information about him Victron BlueSolar PWM Charge Controller-LCD and USB 12 / 24V / 10A
Price without VAT
| Weight | 1 kg |
|---|---|
| Brand |
Related products
Victron BlueSolar PWM-Light 12 / 24V-10A - PWM 10A Charging Regulator for Photovoltaics
22.00 €
19.00 € Excluding VAT
23.56 € Includes VAT
19.00 € Excluding VAT
23.56 € Includes VAT
Victron BlueSolar PWM-Light 12 / 24V-10A - PWM 10A Charging Regulator for Photovoltaics
Programmable with night mode
- The BlueSolar PWM Light 12 / 24V-10A charge controller is ready to use with its default settings.
- Three stages of battery charging
- Battery status check function
- Night operation
- Load output with battery discharge protection, overload protection and short circuit.
- Reverse polarity protection of photovoltaic - battery.
Specifications
| Charge Controller Type | PWM |
|---|---|
| System Voltage | 12V, 24V |
| Permitted Humidity | max. 95% RF (not condensing) |
| IP Protection | IP20 |
| Charging Current max. | 10A |
| Standby Self-Consumption | 10mA |
| Max. Voltage Solar Module | 28V / 55V |
| Max. Current Solar Module | 10A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Available on backorder
CHARGING REGULATOR PHOCOS CX-2048 24 / 48V - 20A
119.16 €
99.00 € Excluding VAT
122.76 € Includes VAT
99.00 € Excluding VAT
122.76 € Includes VAT
Use in small autonomous and large photovoltaic installations. The charge regulator for photovoltaics CX20-48 has an LCD graphic display, which displays the charge status of the battery and the charge, as well as the operation of the photovoltaics.
Price without VAT
In stock
Victron BlueSolar PWM PRO 12 / 24V-20A - PWM Charging Regulator (12 / 24V) 20A for Photovoltaics
51.00 €
43.00 € Excluding VAT
53.32 € Includes VAT
43.00 € Excluding VAT
53.32 € Includes VAT
Victron BlueSolar PWM PRO 12 / 24V-20A - PWM Charging Regulator (12 / 24V) 20A for Photovoltaics
The BlueSolar PWM-Pro series with default operating settings is one of the most advantageous and reliable solutions on the market. The charge regulator BlueSolar PWM-Pro 12 / 24V-20A has three battery charging stages (Bulk, absortion, float) which maximizes the battery life and the smooth operation of your photovoltaic system. It also has protection against short circuits and overvoltages as well as from reverse polarity phenomena of solar panels or the battery. It can also be programmed with the help of the integrated BlueSolar Pro remote control panel easily, quickly and correctly.
Programmable with night mode
- The BlueSolar PWM-Pro 12 / 24V-20A charge controller is ready to use with its default settings. It is also fully programmable with the help of the BlueSolar Pro Remote Panel
- Three stages of battery charging (programmed with the help of BlueSolar Pro Remote Panel)
- Battery status check function (Remote Panel required)
- Night mode (Remote Panel required)
- Load output with battery discharge protection, overload protection and short circuit.
- Reverse polarity protection of photovoltaic - battery.
- Optional external temperature sensor.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 12V, 24V |
| Connectivity | Fananzeige Pro Fanbedienpanel, PWM-Pro with USB Interface Cable, Temperature Turbines |
| Permitted Humidity | max. 98% (not condensing) |
| IP Protection | IP30 |
| Charging Current max. | 20A |
| Standby Self-Consumption | 10mA |
| Max. Voltage Solar Module | 28V / 55V |
| Max. Current Solar Module | 20A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Available on backorder
Epsolar Dual Battery PWM 10A
35.00 €
29.00 € Excluding VAT
35.96 € Includes VAT
29.00 € Excluding VAT
35.96 € Includes VAT
10A Dual Battery PWM charge regulator for 2 batteries.
Feature:
· Two battery charging eliminates the extra cost of two separate solar charging systems
· Intelligent System Optimum Control
· 12 / 24V auto work
· Battery type selection
· Charging frequency optional
· High efficient Series PWM charging
· Local external temperature compensation
· Remote temperature sensor optional
· Use MOSFET as electronic switch, without any mechanical switch
· Remote meter MT-1 optional
· Electronic protection: over charging, short circuit, battery reverse polarity protection
Specification:
| Electrical parameters | |
| System voltage | 12 / 24VDC Auto work |
| Nominal battery current | 10A |
| Charge circuit voltage drop | .0.26V |
| Discharge circuit voltage drop | .0.15V |
| Self consumption | ≤ 6mA |
| Working temperature | -35 ℃ to + 55 ℃ |
| Humidity | 10% -90% NC |
| Enclosure | IP30 |
| Port | 4mm2 |
| Net weight | 0.15KG |
Price without VAT
Cotek CX2425 Battery Charger - 24V - 25A - 230VAC
349.00 €
279.00 € Excluding VAT
345.96 € Includes VAT
279.00 € Excluding VAT
345.96 € Includes VAT
Cotek CX2425 Battery Charger - 24V - 25A - 230VAC
Price without VAT
In stock
Cotek CX2440 Battery Charger - 24V - 40A - 230VAC
495.00 €
379.00 € Excluding VAT
469.96 € Includes VAT
379.00 € Excluding VAT
469.96 € Includes VAT
Cotek CX2440 Battery Charger - 24V - 40A - 230VAC
Price without VAT
In stock
LS2024EPD 20A PWM Charging regulator waterproof
42.00 €
29.90 € Excluding VAT
37.08 € Includes VAT
29.90 € Excluding VAT
37.08 € Includes VAT
Waterproof / watertight charge regulator IP 67 LS2024EPD 20A PWM technology. Suitable for lighting columns, garden lights, yachts, yachts and generally for outdoor use with protection from moisture.
Price without VAT
In stock
LS2024EU 20A PWM-USB Charging regulator
28.00 €
14.50 € Excluding VAT
17.98 € Includes VAT
14.50 € Excluding VAT
17.98 € Includes VAT
LS2024EU 20A PWM charge controller with USB
Ο charge regulator LS2024EU 20A with USB output provides efficient charging by applying the new PWM technology, increasing the battery life and improving the performance of the photovoltaic panels of a system; Load output · Provides battery temperature compensation ensuring proper charging and discharging of parameters automatically.
Features Electronic protection: · Load overload protection · Short circuit protection · Over-discharge battery protection · Reverse battery polarity protection
Price without VAT
Out of stock
Victron BlueSolar PWM PRO 12 / 24V-30A - PWM Charging Regulator (12 / 24V) 30A for Photovoltaics
81.00 €
69.00 € Excluding VAT
85.56 € Includes VAT
69.00 € Excluding VAT
85.56 € Includes VAT
Victron BlueSolar PWM PRO 12 / 24V-30A - PWM Charging Regulator (12 / 24V) 30A for Photovoltaics
The BlueSolar PWM-Pro series is ready to use with the default settings. It has three stages of battery charging (Bulk, absortion, float), protection against short circuit and over-voltages as well as from reverse polarity of the solar panels and / or the battery. These unique features make the BlueSolar PWM -Pro 12 / 24V-10A controller one of the most valuable controllers on the market. It can also be programmed easily, quickly and correctly with the help of the integrated BlueSolar Pro remote control panel.
General characteristics:
- The BlueSolar PWM -Pro 12 / 24V-30A charge controller is ready for use with its default settings. It is also fully programmable with the help of the BlueSolar Pro Remote Panel
- Programmable with night mode
- Three stages of battery charging (programmed with the help of BlueSolar Pro Remote Panel)
- Battery status check function (Remote Panel required)
- Night mode (Remote Panel required)
- Load output with battery discharge protection, overload protection and short circuit.
- Reverse polarity protection of photovoltaic - battery.
- Optional external temperature sensor.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 12V, 24V |
| Connectivity | Fananzeige Pro Fanbedienpanel, PWM-Pro with USB Interface Cable, Temperature Turbines |
| Permitted Humidity | max. 98% (not condensing) |
| IP Protection | IP30 |
| Charging Current max. | 30A |
| Standby Self-Consumption | 10mA |
| Max. Voltage Solar Module | 28V / 55V |
| Max. Current Solar Module | 30A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
| Supported Battery Types | Bleisäure, AGM, Gel |
Available on backorder
10A PWM charge regulator LS1024
19.00 €
11.50 € Excluding VAT
14.26 € Includes VAT
11.50 € Excluding VAT
14.26 € Includes VAT
10A, programmable charge regulator with night mode.
Technical data - programming
| QUICK START INSTRUCTIONS | |||||||||||||||||||||||||||||||||||
| This section provides a brief overview of how to get started using the controller. However, please review the entire manual to ensure best performance and years of trouble-free service. 1. Mount the controller on a vertical surface. Allow space above and below the controller for air flow. 2. Make sure the PV and load currents will not exceed the ratings of the controller being installed. 3. It is recommended that the connections be made in order from 1 to 6. (see the following picture) |
|||||||||||||||||||||||||||||||||||
| 4. Connect the BATTERY first. Use care that bare wires do not touch the metal case of the controller. 5. Connect the SOLAR (PV array) next. The green LED indicator will light if sunlight is present. 6. Connect the LIGHT last. If the red LED indicator lights, the battery capacity is low and should be charged before completing the system installation 7. Press the BUTTON as 6 or 7 to verify the system connection. |
|||||||||||||||||||||||||||||||||||
| 3. Connect the consumer to the charge regulator - plus and minus Please observe that the automatic adjustment to 12V / 24V systems does not function properly, if this sequence order is not followed. An improper sequence order can damage the battery! | |||||||||||||||||||||||||||||||||||
| LIGHTING CONTROL OPTIONS | |||||||||||||||||||||||||||||||||||
| 1. Press the power switch for 5 seconds, and select the desired LIGHTING CONTROL option. The LED is on, which confirms you have selected the right one. 2. The controller requires 10 minutes of continuous transition values before it starts to work. These constraints avoid false transitions due to lightning or dark storm clouds. 3. 10 minutes off before the controller starts to work. 4. A brief description follows below: |
|||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||
Price without VAT
Out of stock
Charging regulator LS1024EU 10A PWM-USB
18.00 €
12.40 € Excluding VAT
15.38 € Includes VAT
12.40 € Excluding VAT
15.38 € Includes VAT
Ο charge regulator LS1024EU 10 provides efficient charging by applying the new PWM technology increasing the battery life and improving the performance of the photovoltaic panels of a system · Has MOSFET as electronic switch, without mechanical switch · Provides LED indicators that inform about the voltage status of the battery · Provides control Load output · Provides battery temperature compensation ensuring proper charging and discharging of parameters automatically.
Features Electronic protection: · Load overload protection · Short circuit protection · Over-discharge battery protection · Reverse battery polarity protection
Price without VAT
Out of stock
Charging regulator LS0512EU 5A PWM
19.00 €
8.50 € Excluding VAT
10.54 € Includes VAT
8.50 € Excluding VAT
10.54 € Includes VAT
Charging regulator LS0512EU 5A PWM with USB output
Specifications:
Ο charge regulator LS0512EU 5A provides efficient charging by applying the new PWM technology, increasing battery life and improving the performance of a system's photovoltaic panels; of the load output · Provides compensation of the temperature of the batteries ensuring proper charging and discharging of the parameters automatically
It has Electronic protection:
· Load overload protection · Short circuit protection · Battery protection against overcharging · Reverse battery polarity protection
Price without VAT
Out of stock
Most viewed products
-
10kW PPC Photovoltaic ECO 545 Solar on roofs
6,800.00 €
5,300.00 € Excluding VAT
6,572.00 € Includes VAT10 Kwatt photovoltaic on roofs with interconnected to PPC photovoltaic system with installation
Photovoltaic Eco 545
See all offers here
Available on backorder
-
5kW PPC Photovoltaic ECO Solar 410-420 WATT with possibility for Installation
7,280.00 €
4,800.00 € Excluding VAT
5,952.00 € Includes VAT
410-WATT-420-WATT-
About answers to the most common questions about photovoltaics in homes. See the special offers of photovoltaics for 2022
5kw with photovoltaics on roofs with photovoltaics and installation Additional offers here
Available on backorder
-
Net metering 5kW photovoltaic package with 450 watt panels
3,650.00 €
2,750.00 € Excluding VAT
3,410.00 € Includes VATNet metering 5kW photovoltaic package offer
11 Photovoltaic panels 450 watts
Network inverter Renac NA 5000 DS (7500WATT max) 10 Year Warranty
Tile roof supports for 11 PV panels.
In stock
-
Autonomous photovoltaic package 1.2kWh/24 hours-12v
599.00 €
465.00 € Excluding VAT
576.60 € Includes VATAvailable on backorder
-
Net metering 10kW energy offset with PPC
6,700.00 €
5,590.00 € Excluding VAT
6,931.60 € Includes VATNet metering 10kW for energy offset and savings with PPC with production up to 16.600kWh per year
Available on backorder
-
Autonomous PV for a holiday home 4,5kWh with air conditioner
2,600.00 €
1,780.00 € Excluding VAT
2,207.20 € Includes VATAutonomous photovoltaic for a 4,5kWh cottage with air conditioning
Available on backorder
-
Net-metering 10kw with 10kwh lithium battery for storage with 460 WATT PV and Panels Complete package
17,800.00 €
14,100.00 € Excluding VAT
17,484.00 € Includes VATNet-metering 10kw with 10kwh lithium battery for storage with PV 460 WATT and Panels Complete AC/DC package for energy compensation (10 year inverter warranty)
Net metering 10kw with 10kwh lithium battery ( They produce in the summer in southern areas 40-50kw daily and about half or 1/3 in Winter) 12.000 - 16.000 kw averaged per year in Southern regions.
Price without VAT
Available on backorder
-
Photovoltaic Luxor 540 watt mono half cell ecoline LX-540M / 182-144-Germany
329.00 €
159.00 € Excluding VAT
197.16 € Includes VAT565 watts now available
LUXOR 565W N-Type TopCon LX-565TC M/144/N-TYPE/FS35/SW/16B/1500V Dimensions 2279x1134x35. Information here
Suitable for net-metering, home photovoltaics, parks and photovoltaic stations
Minimum purchase quantity 9 pieces
Out of stock
-
5 kwh- 7kwh/24v/220AC – 24V Premium Photovoltaic System
3,750.00 €
2,950.00 € Excluding VAT
3,658.00 € Includes VAT4 pcs. Φ / Β panel Solar Energy SE 270 / 270-275 watt Poly/ European. They have positive Photovoltaic system Premium 24V tolerance and power in watts. That is, they always deliver more watts than their rated power, high efficiency installed power 1080 watts up to + 5% more efficiency. Available with 12 years warranty factory equipment and 25 years warranty 80% yield.
1 pc. pure sine wave inverter Phoenix 24/1600 3200 watt power supply high reliability. Suitable for operation of all devices of corresponding power. Provides energy savings of up to 25% on self-consumption due to stabilized sine. Warranty 60 months (5 years)
4 pcs. Batteries S. Energy ECOAGM 220 / 250AH C100 type VRLA/ AGM corresponding specifications to GEL batteries. (deep closed type discharge lasting 10-12 years of life). Total 828AH / 12V
Possibility to add 2V High-strength and longer-lasting batteries in extreme uses at a small additional cost.
1 pc. Charging regulator Phocos CXN 40 (Digital programmable) (2 years warranty)
Ability to add MPPT controller with datalogger to increase efficiency up to 25% at a small additional cost.
Available on backorder
-
Autonomous photovoltaic for caravans or cottages 0,5kWh
630.00 €
495.00 € Excluding VAT
613.80 € Includes VATAvailable on backorder
Recently viewed products
-
Xantrex SW 4548 E
5,096.00 €
3,545.00 € Excluding VAT
4,395.80 € Includes VATConverter 4500 VA 48V with integrated charger and metal relay.
Price without VAT
-
10kW PPC Photovoltaic ECO 545 Solar on roofs
6,800.00 €
5,300.00 € Excluding VAT
6,572.00 € Includes VAT10 Kwatt photovoltaic on roofs with interconnected to PPC photovoltaic system with installation
Photovoltaic Eco 545
See all offers here
Available on backorder
-
5kW On/Off grid inverter Hybrid three phase V-TAC On/off Grid SKU: 11743
2,900.00 €
2,315.00 € Excluding VAT
2,870.60 € Includes VAT5kW On/Off grid inverter V-TAC SKU: 11743 for photovoltaic
Available on backorder
-
Victron Phoenix 12/1200 Schuko outlet * - Pure Sine Inverter with Power 1200 VA for Photovoltaics
425.00 €
300.00 € Excluding VAT
372.00 € Includes VATVictron Phoenix 12/1200 Schuko outlet * - Pure Sine Inverter 12V / 1200VA / 230V for Photovoltaics
The small series of Victron inverters continues to use the proven solution of the complete bridge with a toroidal transformer. The new series, however, has a new casing, new electronics and new software.
The units consist of a steel frame with a plastic cover, while the electronic management of the inverters provides improved dynamic stability of the output voltage. Last but not least is the range of communication and feature configuration options offered by Victron using VE.Direct software.
Technical Characteristics
Power : 1200 VA
Input voltage: 12 V DC
Output voltage: 230 V AC
Έξοδος: SHUKO
Peak power: 2400 W
Performance level : 94%
Available on backorder
-
Blue Power IP67 Charger 24/8 Battery Charger (1 'Output + Si)
174.00 €
147.00 € Excluding VAT
182.28 € Includes VATCharger Blue Power IP 67 fully protected: waterproof, with protection against vibration and ignition
The Blue Power IP67 charger is not at risk from water, oil or dirt. The housing is made of cast aluminum and the electronic components are made of resin molds.Price without VAT -
Wind turbine SA-300 / 360Watt
550.00 €
389.00 € Excluding VAT
482.36 € Includes VATWind turbine SA-300 / 360Watt includes PWM Controller with protection and electronic "braking" worth 100 €.
Price without VAT
Out of stock
-
2.03kW Photovoltaic PPC BASIC
4,060.00 €
2,900.00 € Excluding VAT
3,596.00 € Includes VAT2,03 Kwatt system interconnected with PPC
2.035 watts with photovoltaic Solar Energy Power Plus 185 watts of monocrystalline silicon with positive tolerance and more watts !!!
It produces an average of 2600kw per year (for areas of Attica and further south) while covering an area of 28-32 square meters. It saves 1300-1500 euros per year and depreciates the installation cost in 4.5-5 years.
Price without VAT
In stock
-
Autonomous PV with 1.8kwh to 2kWh installation (small cottage-caravan)
1,780.00 €
1,225.00 € Excluding VAT
1,519.00 € Includes VATAutonomous Photovoltaic with installation up to 2kWh (for small refrigerator, lights, chargers, TV, (small cottage-caravan)
Available on backorder
-
-
Victron Easy Solar 24/1600 / 40-16 MPPT 100/50-Inverter Converter
1,705.00 €
1,307.00 € Excluding VAT
1,620.68 € Includes VATVictron Easy Solar 24/1600 / 40-16 MPPT 100/50-Inverter Converter. Victron inverters are compatible with many solar systems. For grid-connected systems, they can operate with one or two panels as well as with a battery. They also work with off-grid solar systems.
Available on backorder
