Renewable Energy> Photovoltaic-Batteries-Inverters-Regulators
Open Sidebar
-39%LimitedSOLD OUT
solar-charger-rythistis-fortisis-10a-ls1024-pwm.jpg
Add to Compare Added to Compare

10A PWM charge regulator LS1024

Cotek CX1250 Battery Charger - 12V - 50A - 230VAC

279.00 € + VAT

20A Solar Charger PWM LS2024

13.50 € + VAT
19.00 €
11.50 € Excluding VAT
14.26 € Includes VAT

10A, programmable charge regulator with night mode.

 Technical data - programming

QUICK START INSTRUCTIONS  
This section provides a brief overview of how to get started using the controller. However, please review the entire manual to ensure best performance and years of trouble-free service. 
1. Mount the controller on a vertical surface. Allow space above and below the controller for air flow. 
2. Make sure the PV and load currents will not exceed the ratings of the controller being installed. 
3. It is recommended that the connections be made in order from 1 to 6. (see the following picture)
 
4. Connect the BATTERY first. Use care that bare wires do not touch the metal case of the controller. 
5. Connect the SOLAR (PV array) next. The green LED indicator will light if sunlight is present. 
6. Connect the LIGHT last. If the red LED indicator lights, the battery capacity is low and should be charged before completing the system installation 
7. Press the BUTTON as 6 or 7 to verify the system connection.
3. Connect the consumer to the charge regulator - plus and minus Please observe that the automatic adjustment to 12V / 24V systems does not function properly, if this sequence order is not followed. An improper sequence order can damage the battery!
LIGHTING CONTROL OPTIONS
1. Press the power switch for 5 seconds, and select the desired LIGHTING CONTROL option. The LED is on, which confirms you have selected the right one. 
2. The controller requires 10 minutes of continuous transition values ​​before it starts to work. These constraints avoid false transitions due to lightning or dark storm clouds. 
3. 10 minutes off before the controller starts to work. 
4. A brief description follows below:
　0,1,2,3,4,5,6,7 　For DC output
　0 　Dusk-to-Dawn, light is on all light
　1 　1 hours light is turned on after sunset
　2 　2 hours light is turned on after sunset
　3 　3 hours light is turned on after sunset
　4 　4 hours light is turned on after sunset
　5 　5 hours light is turned on after sunset
　6 　6 hours light is turned on after sunset
　7 　7 hours light is turned on after sunset
　0. 　8 hours light is turned on after sunset
　1. 　9 hours light is turned on after sunset
　2. 　10 hours light is turned on after sunset
　3. 　11 hours light is turned on after sunset
　4. 　12 hours light is turned on after sunset
　5. 　13 hours light is turned on after sunset
　6. 　Lights remain turned off, ON / OFF mode
　7. 　Test mode, lights on after it detects no light, lights off after it detects light.

 

Price without VAT

Out of stock

  ... people are viewing this right now
  Share

The 10A, programmable charge controller with night mode in black or white. It has a PWM microprocessor for more efficient and smoother charging. Also programmable for Night mode. It has a light sensor and a timer. It includes connectors for devices that are programmed to operate at night while at the same time they are switched off according to the respective programming.

 Technical data - programming

QUICK START INSTRUCTIONS  
This section provides a brief overview of how to get started using the controller. However, please review the entire manual to ensure best performance and years of trouble-free service. 
1. Mount the controller on a vertical surface. Allow space above and below the controller for air flow. 
2. Make sure the PV and load currents will not exceed the ratings of the controller being installed. 
3. It is recommended that the connections be made in order from 1 to 6. (see the following picture)
 
4. Connect the BATTERY first. Use care that bare wires do not touch the metal case of the controller. 
5. Connect the SOLAR (PV array) next. The green LED indicator will light if sunlight is present. 
6. Connect the LIGHT last. If the red LED indicator lights, the battery capacity is low and should be charged before completing the system installation 
7. Press the BUTTON as 6 or 7 to verify the system connection.
3. Connect the consumer to the charge regulator - plus and minus Please observe that the automatic adjustment to 12V / 24V systems does not function properly, if this sequence order is not followed. An improper sequence order can damage the battery!
LIGHTING CONTROL OPTIONS
1. Press the power switch for 5 seconds, and select the desired LIGHTING CONTROL option. The LED is on, which confirms you have selected the right one. 
2. The controller requires 10 minutes of continuous transition values ​​before it starts to work. These constraints avoid false transitions due to lightning or dark storm clouds. 
3. 10 minutes off before the controller starts to work. 
4. A brief description follows below:
　0,1,2,3,4,5,6,7 　For DC output
　0 　Dusk-to-Dawn, light is on all light
　1 　1 hours light is turned on after sunset
　2 　2 hours light is turned on after sunset
　3 　3 hours light is turned on after sunset
　4 　4 hours light is turned on after sunset
　5 　5 hours light is turned on after sunset
　6 　6 hours light is turned on after sunset
　7 　7 hours light is turned on after sunset
　0. 　8 hours light is turned on after sunset
　1. 　9 hours light is turned on after sunset
　2. 　10 hours light is turned on after sunset
　3. 　11 hours light is turned on after sunset
　4. 　12 hours light is turned on after sunset
　5. 　13 hours light is turned on after sunset
　6. 　Lights remain turned off, ON / OFF mode
　7. 　Test mode, lights on after it detects no light, lights off after it detects light.

 

Price without VAT

Weight 1 kg
Brand

SKU: 10A PWM charge regulator LS1024 Categories: , , , , ,

you may also like...

-16%Limited
Add to cart
Victron BlueSolar
Victron BlueSolar PWM PRO 12 / 24V-20A - PWM Charging Regulator (12 / 24V) 20A for Photovoltaics 51.00 €
43.00 € Excluding VAT
53.32 € Includes VAT

Victron BlueSolar PWM PRO 12 / 24V-20A - PWM Charging Regulator (12 / 24V) 20A for Photovoltaics

The BlueSolar PWM-Pro series with default operating settings is one of the most advantageous and reliable solutions on the market. The charge regulator BlueSolar PWM-Pro 12 / 24V-20A has three battery charging stages (Bulk, absortion, float) which maximizes the battery life and the smooth operation of your photovoltaic system. It also has protection against short circuits and overvoltages as well as from reverse polarity phenomena of solar panels or the battery. It can also be programmed with the help of the integrated BlueSolar Pro remote control panel easily, quickly and correctly.

Programmable with night mode

  1. The BlueSolar PWM-Pro 12 / 24V-20A charge controller is ready to use with its default settings. It is also fully programmable with the help of the BlueSolar Pro Remote Panel
  2. Three stages of battery charging (programmed with the help of BlueSolar Pro Remote Panel)
  3. Battery status check function (Remote Panel required)
  4. Night mode (Remote Panel required)
  5. Load output with battery discharge protection, overload protection and short circuit.
  6. Reverse polarity protection of photovoltaic - battery.
  7. Optional external temperature sensor.

 Specifications

 

Manufacturer VictronEnergy
Charge Controller Type PWM
System Voltage 12V, 24V
Connectivity Fananzeige Pro Fanbedienpanel, PWM-Pro with USB Interface Cable, Temperature Turbines
Permitted Humidity max. 98% (not condensing)
IP Protection IP30
Charging Current max. 20A
Standby Self-Consumption 10mA
Max. Voltage Solar Module 28V / 55V
Max. Current Solar Module 20A
Number of Charging Outputs 1
Ambient Temperature -20 ° C - + 50 ° C

 

Available on backorder

-15%Limited
Add to cart
Bluesolar PWM Light 48V-30A
Victron BlueSolar PWM Light 48V / 30A - PWM 30A Charging Regulator for Photovoltaics 66.00 €
56.00 € Excluding VAT
69.44 € Includes VAT

Victron BlueSolar PWM Light 48V-30A - PWM 30A Charging Regulator for Photovoltaics

The charging regulator Victron Victron Bluesolar PWM Light 48V-30A, has an internal temperature sensor and consists of an advanced system of three stages of battery charging (Bulk, absortion, float) that ensures the correct charging process of your battery is charged resulting in maximizing life her! It is a very reliable charge regulator with protection against short circuits and overvoltages as well as from reverse polarity phenomena of solar panels and / or the battery. The charge regulator Victron Victron Bluesolar PWM Light 48V-30A is suitable for photovoltaic systems, for charging the batteries with current up to 30A.

Specifications

Manufacturer VictronEnergy
Charge Controller Type PWM
System Voltage 48V
Permitted Humidity max. 95% RF (not condensing)
IP Protection IP20
Charging Current max. 30A
Standby Self-Consumption 10mA
Max. Voltage Solar Module 100V
Max. Current Solar Module 30A
Number of Charging Outputs 1
Ambient Temperature -20 ° C - + 50 ° C

Available on backorder

-14%Limited
Add to cart
Victron BlueSolar PWM PRO 10A
Victron BlueSolar PWM PRO 10A 29.00 €
25.00 € Excluding VAT
31.00 € Includes VAT

Victron BlueSolar PWM PRO 12 / 24V-10A - PWM Charging Regulator (12 / 24V) 10A for Photovoltaics

The BlueSolar PWM-Pro series is ready to use with the default settings. It has three stages of battery charging (Bulk, absortion, float), protection against short circuit and over-voltages as well as from reverse polarity of the solar panels and / or the battery. These unique features make the BlueSolar PWM -Pro 12 / 24V-10A controller one of the most valuable controllers on the market. It can also be programmed easily, quickly and correctly with the help of the integrated BlueSolar Pro remote control panel.

Specifications 

Manufacturer VictronEnergy
Charge Controller Type PWM
System Voltage 12V, 24V
Connectivity Fananzeige Pro Fanbedienpanel, PWM-Pro with USB Interface Cable, Temperature Turbines
Permitted Humidity max. 98% (not condensing)
IP Protection IP30
Charging Current max. 10A
Standby Self-Consumption 10mA
Max. Voltage Solar Module 28V / 55V
Max. Current Solar Module 10A
Number of Charging Outputs 1
Ambient Temperature -20 ° C - + 50 ° C

Price without VAT

Available on backorder

-48%LimitedSOLD OUT
read more
LS2024EU 20A PWM-USB Charging regulator 28.00 €
14.50 € Excluding VAT
17.98 € Includes VAT

LS2024EU 20A PWM charge controller with USB

Ο charge regulator LS2024EU 20A with USB output provides efficient charging by applying the new PWM technology, increasing the battery life and improving the performance of the photovoltaic panels of a system; Load output · Provides battery temperature compensation ensuring proper charging and discharging of parameters automatically.

Features Electronic protection: · Load overload protection · Short circuit protection · Over-discharge battery protection · Reverse battery polarity protection

Price without VAT

Out of stock

Related products

-15%Limited
Add to cart
Victron MPPT 10A Special Offer
Victron BlueSolar MPPT 75/10 - Charging Regulator 10A-MPPT for Photovoltaic-Wind Turbines 48.00 €
41.00 € Excluding VAT
50.84 € Includes VAT

Victron BlueSolar MPPT 75/10 - MPPT Charging Regulator 10A for Photovoltaic-Wind Turbines

Victron battery chargers, thanks to fast technology maximum power point (MPPT) from photovoltaic panels, even under shading conditions, promise the fastest possible charging of the batteries of the autonomous photovoltaic system, based on the safety of the equipment and ensuring the required charging voltage of the batteries for their proper and long-term proper operation.

They have extremely fast find the maximum power efficiency point (MPPT). Especially in the case of cloudy skies, or when the light intensity is constantly changing, an ultra-fast MPPT controller will improve energy efficiency by up to 30% compared to PWM charge controllers of up to 10% compared to slower MPPT controllers.

 

Specifications

 

Type MPPT
Power (W) 145 (12V) / 290 (24V)
Manufacturer VictronEnergy
Input voltage (V) 75
Output Voltage (V) 12/24
IP Protection IP43 (electronic components), IP22 (connection area)
Weight (kg) 0.5
Warranty (years) 5 years
Other Information Color Blue (RAL 5012), 6 mm² / AWG10 (Power terminals), VE.Direct

 

Available on backorder

-16%Limited
Add to cart
Victron BlueSolar PWM
Victron BlueSolar PWM Light 12 / 24V-30A - PWM 30A Charging Regulator for Photovoltaics 44.00 €
37.00 € Excluding VAT
45.88 € Includes VAT

Victron BlueSolar PWM Light 12 / 24V-30A - PWM 30A Charging Regulator for Photovoltaics

Charging regulator of Victron BlueSolar PWM Light 12 / 24V-30A includes internal temperature sensor. It consists of three stages of battery charging (Bulk, abortion, float), has an advanced protection system against short circuits and over-voltages.

Specifications : 

  • Battery Voltage: 12 / 24V (Automatic selection)
  • Night mode (details in the Remote Panel manual)
  • Rated charging current: 30 A
  • Second battery output: not available
  • Automatic load disconnection: Yes (maximum load 30A)
  • Maximum input voltage of PV panel: 28V / 55V
  • Self-consumption: <10mA
  • Protection: battery reverse polarity, short circuit, overheating
  • Operating temperature range -20 to +50 C
  • Absorption charge (default): 14.4V (12V) / 28.8V (24V)
  • Float charge (default): 13.8V (12V) / 27.6V (24V)
  • Equalization charge (default): 14.6V (12V) / 29.2V (24V)
  • Load disconnection voltage (default): 11.1V (12V) / 22.2V (24V)
  • Load reconnection voltage (default): 12.6V (12V) / 25.2V (24V)
  • Protection class (dust-humidity): IP 30
  • Dimensions: 138x70x37 mm
  • Warranty: 5 Years

Available on backorder

-13%LimitedSOLD OUT
read more
Phocos CXN 20 CHARGING REGULATOR PHOCOS 12V-24V 20A for autonomous photovoltaics
Phocos CXN 20 69.00 €
60.00 € Excluding VAT
74.40 € Includes VAT

 Phocos CXN 20 CHARGING REGULATOR PHOCOS 12V-24V 20A for autonomous photovoltaics

Price without VAT

Out of stock

-23%Limited
Add to cart
Cotek CX2440 Battery Charger - 24V - 40A - 230VAC 495.00 €
379.00 € Excluding VAT
469.96 € Includes VAT

Cotek CX2440 Battery Charger - 24V - 40A - 230VAC 

Price without VAT

In stock

-14%Limited
Add to cart
Victron BlueSolar PWM-Light
Victron BlueSolar PWM-Light 12 / 24V-10A - PWM 10A Charging Regulator for Photovoltaics 22.00 €
19.00 € Excluding VAT
23.56 € Includes VAT

Victron BlueSolar PWM-Light 12 / 24V-10A - PWM 10A Charging Regulator for Photovoltaics

Programmable with night mode

  1. The BlueSolar PWM Light 12 / 24V-10A charge controller is ready to use with its default settings.
  2. Three stages of battery charging
  3. Battery status check function
  4. Night operation
  5. Load output with battery discharge protection, overload protection and short circuit.
  6. Reverse polarity protection of photovoltaic - battery.

Specifications

Charge Controller Type PWM
System Voltage 12V, 24V
Permitted Humidity max. 95% RF (not condensing)
IP Protection IP20
Charging Current max. 10A
Standby Self-Consumption 10mA
Max. Voltage Solar Module 28V / 55V
Max. Current Solar Module 10A
Number of Charging Outputs 1
Ambient Temperature -20 ° C - + 50 ° C

 

Available on backorder

-55%LimitedSOLD OUT
read more
Charging regulator LS0512EU 5A PWM 19.00 €
8.50 € Excluding VAT
10.54 € Includes VAT

Charging regulator LS0512EU 5A PWM with USB output

 Specifications:

Ο charge regulator LS0512EU 5A provides efficient charging by applying the new PWM technology, increasing battery life and improving the performance of a system's photovoltaic panels; of the load output · Provides compensation of the temperature of the batteries ensuring proper charging and discharging of the parameters automatically

It has Electronic protection:

· Load overload protection · Short circuit protection · Battery protection against overcharging · Reverse battery polarity protection

Price without VAT

Out of stock

-15%Limited
Add to cart
Victron BlueSolar PWM
Victron BlueSolar PWM PRO 12 / 24V-5A - PWM Charging Regulator (12 / 24V) 5A for Photovoltaics 26.00 €
22.00 € Excluding VAT
27.28 € Includes VAT

Victron BlueSolar PWM PRO 12 / 24-5A - PWM Charging Regulator (12 / 24V) 5A for Photovoltaics

The BlueSolar PWM-Pro series is ready to use with the default settings. It has three stages of battery charging (Bulk, abortion, float), protection against short circuit and over-voltages as well as from reverse polarity of the solar panels and / or the battery. In this way your battery is charged in the best way resulting in its much longer life while ensuring the smooth operation of your photovoltaic system. Also the charge regulator BlueSolar PWM-Pro 12 / 24V-5A Victron can be programmed with the help of the integrated BlueSolar Pro remote control panel making it one of the best choices on the market.

Specifications

Manufacturer VictronEnergy
Charge Controller Type PWM
System Voltage 12V
Permitted Humidity max. 95% RF (not condensing)
IP Protection IP20
Charging Current max. 5A
Standby Self-Consumption 10mA
Battery Voltage 12V, 24V
Load Current max. 5A
Max. Voltage Solar Module 28V / 55V
Max. Current Solar Module 5A
Number of Charging Outputs 1
Ambient Temperature -20 ° C - + 50 ° C

Available on backorder

-16%LimitedSOLD OUT
read more
Charging Regulator Victron Bluesolar PWM Duo 12 / 24-20A 91.00 €
76.00 € Excluding VAT
94.24 € Includes VAT

Charging regulator of Victron BlueSolar PWM DUO 12 / 24V-20A includes internal temperature sensor for smooth operation of the regulator. Also with its two outputs it allows the simultaneous charging of batteries. In addition, it includes three stages of battery charging (Bulk, absortion, float), which ensure the maximum charge of the battery, which in turn ensures the smooth operation of your photovoltaic system. The BlueSolar PWM DUO 12 / 24V-20A charge regulator also includes an advanced protection system against short circuits and overvoltages as well as from reverse polarity effects of the solar panels or the battery itself.

 

Charging Regulator, with 2 outputs for charging Batteries

  1. PWM controller
  2. Charges two separate batteries. E.g. the starter battery or the operating battery of the boat or caravan
  3. Programmable charging current ratio (normal setting: equal current for both batteries)
  4. Charging voltage regulation of three types of batteries (Gel, AGM and Flooded)
  5. Internal heat sensor and optional remote control heat sensor
  6. It is protected from overvoltage
  7. It is protected against short circuits
  8. It is protected from reverse polarity of photovoltaic panels and / or batteries.

Price without VAT

Out of stock

-25%LimitedSOLD OUT
read more
Hybrid Controller 600W 199.00 €
149.00 € Excluding VAT
184.76 € Includes VAT

Hybrid controller SAC SSWC-06-1224 with Digital Display
PMW technology,
Reinforced circuit.
12V / 24V operation. Automatic Identification System.

 

Price without VAT

Out of stock

-15%Limited
Add to cart
Victron BlueSolar PWM PRO
Victron BlueSolar PWM PRO 12 / 24V-30A - PWM Charging Regulator (12 / 24V) 30A for Photovoltaics 81.00 €
69.00 € Excluding VAT
85.56 € Includes VAT

Victron BlueSolar PWM PRO 12 / 24V-30A - PWM Charging Regulator (12 / 24V) 30A for Photovoltaics

The BlueSolar PWM-Pro series is ready to use with the default settings. It has three stages of battery charging (Bulk, absortion, float), protection against short circuit and over-voltages as well as from reverse polarity of the solar panels and / or the battery. These unique features make the BlueSolar PWM -Pro 12 / 24V-10A controller one of the most valuable controllers on the market. It can also be programmed easily, quickly and correctly with the help of the integrated BlueSolar Pro remote control panel.

General characteristics:

  1. The BlueSolar PWM -Pro 12 / 24V-30A charge controller is ready for use with its default settings. It is also fully programmable with the help of the BlueSolar Pro Remote Panel
  2. Programmable with night mode
  3. Three stages of battery charging (programmed with the help of BlueSolar Pro Remote Panel)
  4. Battery status check function (Remote Panel required)
  5. Night mode (Remote Panel required)
  6. Load output with battery discharge protection, overload protection and short circuit.
  7. Reverse polarity protection of photovoltaic - battery.
  8. Optional external temperature sensor.

Specifications 

Manufacturer VictronEnergy
Charge Controller Type PWM
System Voltage 12V, 24V
Connectivity Fananzeige Pro Fanbedienpanel, PWM-Pro with USB Interface Cable, Temperature Turbines
Permitted Humidity max. 98% (not condensing)
IP Protection IP30
Charging Current max. 30A
Standby Self-Consumption 10mA
Max. Voltage Solar Module 28V / 55V
Max. Current Solar Module 30A
Number of Charging Outputs 1
Ambient Temperature -20 ° C - + 50 ° C
Supported Battery Types Bleisäure, AGM, Gel

 

Available on backorder

-22%Limited
Add to cart
CHARGING REGULATOR PHOCOS CX-10 12V-24V-10A 37.00 €
29.00 € Excluding VAT
35.96 € Includes VAT

System voltage: 12V / 24V automatic selection. Maximum charging / load current: 10A / 10A Same consumption: operating temperature: -20 ~ + 50⁰C Dimensions: 92 x 93 x 38 mm Weight: 168gr Protection: IP22

Price without VAT

In stock

-20%LimitedSOLD OUT
read more
Waterproof charging regulator LS1024EPD 10A PWM 25.00 €
20.00 € Excluding VAT
24.80 € Includes VAT

Waterproof / watertight charge regulator IP 67  LS1024EPD 10A  PWM technology. Suitable for lighting columns, garden lights, yachts, yachts and generally for outdoor use with protection from moisture.

Price without VAT

Out of stock

Most viewed products

Recently viewed products

  • -30%Limited
    Add to cart
    Victron Gel 130Ah C20
    Victron Gel 130Ah C20 457.00 €
    321.00 € Excluding VAT
    398.04 € Includes VAT

    130AH C20 / 120AH ​​C10- Gel battery for autonomous photovoltaic systems.

    AGM range batteries are characterized by very low internal resistance, which makes them particularly suitable for high-intensity discharge applications such as inverters, propulsion motors and starting motors.
    The range of GEL models provides the best deep cycle durability and longer life.

    Price without VAT

    Available on backorder

  • -15%Limited
    Add to cart
    Victron Gel 165Ah C20 battery for autonomous photovoltaics
    Victron Gel 165Ah C20 battery 460.00 €
    389.00 € Excluding VAT
    482.36 € Includes VAT

    165AH C20 / 150AH ​​C10- Gel battery for autonomous photovoltaic systems.

    AGM range batteries are characterized by very low internal resistance, which makes them particularly suitable for high-intensity discharge applications such as inverters, propulsion motors and starting motors.
    The range of GEL models provides the best deep cycle durability and longer life.
    Collection from the warehouses.

    Price without VAT

    Available on backorder

  • -37%Limited
    Add to cart
    Photovoltaic Panel - Panel Solar SE 100 watt 116.60 €
    73.00 € Excluding VAT
    90.52 € Includes VAT

    Solar Energy 100watt -103 watts high efficiency polycrystalline silicon with 10 years factory hardware warranty & 25 years power efficiency guarantee at 80%.

    Price without VAT

  • -22%Limited
    Add to cart
    Lithium Battery ULM-12-300 Ultimatron LiFePO4 Lithium Battery 12.8V 300Ah / 3840 Wh / with bluetooth and smart BMS with 5 YEAR warranty
    ULM-12-300 Ultimatron Lithium Battery 2,230.00 €
    1,750.00 € Excluding VAT
    2,170.00 € Includes VAT

     ULM-12-300 Ultimatron Lithium Battery

    Minimum order 2 pieces. Delivery 4-6 days from France

  • -20%LimitedSOLD OUT
    read more
    NAKAYAMA-SP9700-017172-Pump-petrol-four-stroke-2.5hp-
    NAKAYAMA SP9700 PETROL PUMP 4 YEARS SP9700 017172 99.00 €
    78.83 € Excluding VAT
    97.75 € Includes VAT

    NAKAYAMA SP9700 PETROL PUMP 4 YEARS SP9700 017172 

    4-year-old engine
    Nakayama OHV
    Power 2.5hp
    Cubic capacity 97cc
    Maximum Flow 200L / min
    Manometric 12m
    Nozzle Ø1 ”½ χ1” ½

    Out of stock

  • -37%LimitedSOLD OUT
    read more
    Wind turbine 1000 -1100 watts up to 1500 watts / 24v 1,580.00 €
    995.00 € Excluding VAT
    1,233.80 € Includes VAT

    Wind turbine 1000 watt - 1100 watt 24v with maximum power / 1500 watt * max / 24v high quality aluminum and Marine type durability for use near the sea.

    Price without VAT

    Out of stock

  • -20%Limited
    Add to cart
    SolarFam VM II Innovation
    SolarFam VM II Innovation 900.00 €
    719.00 € Excluding VAT
    891.56 € Includes VAT

    SolarFam REVO VM II Series 3.5 Any Grid Hybrid Inverter Imported from Holland-3500W / 24V MPPT 500V/100A

    SolarFam REVO VM II Series 3.5 The revolution in inverters – autonomous and interconnected home systems

    The only one capable of operation even WITHOUT BATTERIES

    Available on backorder

  • -49%Limited
    Add to cart
    Yingli YL 235 P-29b 230wp 3kw (1.00 euros / per watt) 5,900.00 €
    2,990.00 € Excluding VAT
    3,707.60 € Includes VAT

    Polycrystalline silicon 230 watts (wp). European certification. Minimum order 3.00 kw 13 pieces x 230 watts (wp) (1.00 euros / per watt).

    Price without VAT

    In stock

  • -19%Limited
    Add to cart
    Victron 12V/100Ah AGM Super Cycle (M6) battery, photovoltaic
    Victron 12V/100Ah AGM Super Cycle Battery (M6) 342.00 €
    276.00 € Excluding VAT
    342.24 € Includes VAT

    Victron 12V/100Ah AGM Super Cycle battery

    Victron 12V/100Ah AGM Super Cycle (M6) deep discharge closed type photovoltaic battery from Victron Energy for high starting amperes.

    Available on backorder

  • -16%Limited
    Add to cart
    Pure Sine Inverter Premium SK - 1200-S-TY-12V 379.00 €
    319.00 € Excluding VAT
    395.56 € Includes VAT

    Product Name: Premium SK - 1200-S-TY-12V

    Voltage: 12V

    Series: Premium S with built-in digital display

    Powerful and reliable Inverter pure sine  Premium SK - 1200-S-TY-12V from high-efficiency Solar Energy with energy savings in relation to the self-consumption of powered appliances up to 25%. The pure sine wave converter provides an output voltage waveform that has very low harmonic distortion. Suitable for all devices with this voltage and operating frequency. It also supports devices that have a high current requirement when starting. The product complies with the standards of quality, safety and good operation of European markets - German technology.

    Use: caravans, yachts, boats, photovoltaic systems, hybrid systems, caravans, compressors, air conditioners, engines, pumps, remote storage, household electrical appliances, office electrical appliances, computers, laptops, mobile phone chargers, etc. Inverters of this type can also prevent computer errors, noise and malfunctions on screens, TVs, game consoles, etc. At the same time they are a reliable source of power for all your electronic devices.

    Product Warranty: 30 Months

    In stock

PWM Solar Charger 10A, charge regulator,

PWM Solar Charger 10A, charge regulator,

Regulator Programmable with night mode - PWM Solar Charger 10A, has a light sensor and timer, prices

My cart
Close Wishlist
Close Recently Viewed
Compare Products (0 Products)
Compare Products
Compare Products
Compare Products
Compare Products
Clear All Let's Compare!
Category