Autonomous photovoltaic system for refrigerator 12V / 65watt - 75 watts
Autonomous photovoltaic kit / package for small refrigerator 65-75 watt / 12V or 220V by adding inverter
10A digital solar charge regulator with Liquid crystal display and USB for 150 Watt / 12v or 300watt / 24v polycrystalline silicon photovoltaic panels
Solar Charge Controller 10A For status monitoring and regulation
Output loading
10A Digital Solar Charger with Liquid Crystal Display for photovoltaic panels
Solar Charge Controller 10A Battery overcharging can be avoided by connecting all loads to the load output. The load output
will disconnect the load when the battery is discharged to a predetermined voltage.
Some loads (especially inverters) can best be connected directly to the battery and remote control
control connected to the load output. You may need a special interface cable, refer to the manual.
The connection and disconnection voltages are adjustable.
Day / night timing of cargo output
This option allows a preset ON-time after dusk.
Programmable battery charging algorithm
Pre-programmed algorithms for AGM, GEL, Flooded or LiFePO4 batteries (only with internal BMS)
Two 5 Volt USB outputs
Maximum current (both outputs combined): 2A
Beware of cheap imitations
Specifications: 10A digital charge regulator with Liquid crystal display for photovoltaic panels:
• Rated voltage: 12V 24V Auto
• Application: Solar system controller
• Current: 10A
• With timer and light sensor, it could work for the sunlight system.
• Only for off-grid photovoltaic system.
Safety instructions:
• 1. Make sure your battery has enough voltage for the controller to recognize the battery type before the first installation.
• 2.The battery cable should be as small as possible to minimize loss.
• 3. The regulator is only suitable for lead acid batteries: OPEN, AGM, GEL is not suitable for nickel hydride, lithium ions or other batteries.
• 4. The charge regulator is only suitable for setting solar modules. Never connect another charging source to the charger.
Character:
• 1. Built-in industrial microcontroller.
• 2. One key setting, digital display, automatic memory function.
• 3. Complete 4-stage PWM charge management.
• 4.Short circuit protection, open circuit protection, reverse protection, protection
overload • 5. Dual reverse current protection, low heat output.
System connection:
• 1. Connect the battery to the charge controller - plus and minus. 1 will be displayed if it detects a 12V battery, 2 if it detects a 24V battery.
• 2. Connect the PV module to the regulator - plus and minus.
• 3. Connect the consumer to the charge controller - plus and minus.
• The reverse order applies when uninstalling!
• An improper sequence can damage the controller!
• Size: 133x70x32mm / 5.2×2.7×1.3”
Note:
• Allow 0-2mm error due to manual measurement.
Price without VAT
| Weight | 1 kg |
|---|---|
| Brand |
Related products
LS2024EPD 20A PWM Charging regulator waterproof
42.00 €
29.90 € Excluding VAT
37.08 € Includes VAT
29.90 € Excluding VAT
37.08 € Includes VAT
Waterproof / watertight charge regulator IP 67 LS2024EPD 20A PWM technology. Suitable for lighting columns, garden lights, yachts, yachts and generally for outdoor use with protection from moisture.
Price without VAT
In stock
Cotek CX1280 Battery Charger - 12V - 80A - 230VAC
679.00 €
499.00 € Excluding VAT
618.76 € Includes VAT
499.00 € Excluding VAT
618.76 € Includes VAT
Cotek CX1280 Battery Charger - 12V - 80A - 230VAC
Price without VAT
In stock
Victron BlueSolar PWM-Light 12 / 24V-10A - PWM 10A Charging Regulator for Photovoltaics
22.00 €
19.00 € Excluding VAT
23.56 € Includes VAT
19.00 € Excluding VAT
23.56 € Includes VAT
Victron BlueSolar PWM-Light 12 / 24V-10A - PWM 10A Charging Regulator for Photovoltaics
Programmable with night mode
- The BlueSolar PWM Light 12 / 24V-10A charge controller is ready to use with its default settings.
- Three stages of battery charging
- Battery status check function
- Night operation
- Load output with battery discharge protection, overload protection and short circuit.
- Reverse polarity protection of photovoltaic - battery.
Specifications
| Charge Controller Type | PWM |
|---|---|
| System Voltage | 12V, 24V |
| Permitted Humidity | max. 95% RF (not condensing) |
| IP Protection | IP20 |
| Charging Current max. | 10A |
| Standby Self-Consumption | 10mA |
| Max. Voltage Solar Module | 28V / 55V |
| Max. Current Solar Module | 10A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Available on backorder
Charging Regulator LS3024 30A PWM
34.10 €
27.00 € Excluding VAT
33.48 € Includes VAT
27.00 € Excluding VAT
33.48 € Includes VAT
30A continuous operation and programmable charge regulator.
Price without VAT
Out of stock
Victron BlueSolar PWM PRO 12 / 24V-5A - PWM Charging Regulator (12 / 24V) 5A for Photovoltaics
26.00 €
22.00 € Excluding VAT
27.28 € Includes VAT
22.00 € Excluding VAT
27.28 € Includes VAT
Victron BlueSolar PWM PRO 12 / 24-5A - PWM Charging Regulator (12 / 24V) 5A for Photovoltaics
The BlueSolar PWM-Pro series is ready to use with the default settings. It has three stages of battery charging (Bulk, abortion, float), protection against short circuit and over-voltages as well as from reverse polarity of the solar panels and / or the battery. In this way your battery is charged in the best way resulting in its much longer life while ensuring the smooth operation of your photovoltaic system. Also the charge regulator BlueSolar PWM-Pro 12 / 24V-5A Victron can be programmed with the help of the integrated BlueSolar Pro remote control panel making it one of the best choices on the market.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 12V |
| Permitted Humidity | max. 95% RF (not condensing) |
| IP Protection | IP20 |
| Charging Current max. | 5A |
| Standby Self-Consumption | 10mA |
| Battery Voltage | 12V, 24V |
| Load Current max. | 5A |
| Max. Voltage Solar Module | 28V / 55V |
| Max. Current Solar Module | 5A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Available on backorder
Victron BlueSolar PWM Light 48V / 10A - PWM 10A Charging Regulator for Photovoltaics
63.00 €
49.00 € Excluding VAT
60.76 € Includes VAT
49.00 € Excluding VAT
60.76 € Includes VAT
Victron BlueSolar PWM Light 48V / 10A - PWM 10A Charging Regulator for Photovoltaics
Its charge regulator Victron Bluesolar PWM Light 48V-10A is compatible with European standards EN60335-1, EMC EN61000-6-1, EN61000-6-3. You do not want to be frustrated if you cannot get the right pitch so invest in a good capo that will extend your life for a while.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 48V |
| Permitted Humidity | max. 95% RF (not condensing) |
| IP Protection | IP20 |
| Charging Current max. | 10A |
| Standby Self-Consumption | 10mA |
| Max. Voltage Solar Module | 100V |
| Max. Current Solar Module | 10A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Available on backorder
Victron BlueSolar PWM Light 48V / 30A - PWM 30A Charging Regulator for Photovoltaics
66.00 €
56.00 € Excluding VAT
69.44 € Includes VAT
56.00 € Excluding VAT
69.44 € Includes VAT
Victron BlueSolar PWM Light 48V-30A - PWM 30A Charging Regulator for Photovoltaics
The charging regulator Victron Victron Bluesolar PWM Light 48V-30A, has an internal temperature sensor and consists of an advanced system of three stages of battery charging (Bulk, absortion, float) that ensures the correct charging process of your battery is charged resulting in maximizing life her! It is a very reliable charge regulator with protection against short circuits and overvoltages as well as from reverse polarity phenomena of solar panels and / or the battery. The charge regulator Victron Victron Bluesolar PWM Light 48V-30A is suitable for photovoltaic systems, for charging the batteries with current up to 30A.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 48V |
| Permitted Humidity | max. 95% RF (not condensing) |
| IP Protection | IP20 |
| Charging Current max. | 30A |
| Standby Self-Consumption | 10mA |
| Max. Voltage Solar Module | 100V |
| Max. Current Solar Module | 30A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Available on backorder
CHARGING REGULATOR PHOCOS CX-2048 24 / 48V - 20A
119.16 €
99.00 € Excluding VAT
122.76 € Includes VAT
99.00 € Excluding VAT
122.76 € Includes VAT
Use in small autonomous and large photovoltaic installations. The charge regulator for photovoltaics CX20-48 has an LCD graphic display, which displays the charge status of the battery and the charge, as well as the operation of the photovoltaics.
Price without VAT
In stock
Victron BlueSolar PWM-Light 12 / 24V-5A - PWM 5A Charging Regulator for Photovoltaics
19.00 €
16.00 € Excluding VAT
19.84 € Includes VAT
16.00 € Excluding VAT
19.84 € Includes VAT
Victron BlueSolar PWM-Light 12 / 24V-5A - PWM 5A Charging Regulator for Photovoltaics
Victron charge regulator with internal temperature sensor. It has three stages of battery charging (Bulk, absortion, float), protection against short circuit and over-voltages as well as from reverse polarity of the solar panels and / or the battery.
Programmable with night mode
- The BlueSolar PWM Light 12 / 24V-5A charge controller is ready to use with its default settings.
- Three stages of battery charging
- Battery status check function
- Night operation
- Load output with battery discharge protection, overload protection and short circuit.
- Reverse polarity protection of photovoltaic - battery.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 12V |
| Permitted Humidity | max. 95% RF (not condensing) |
| IP Protection | IP20 |
| Charging Current max. | 5A |
| Standby Self-Consumption | 10mA |
| Battery Voltage | 12V, 24V |
| Load Current max. | 5A |
| Max. Voltage Solar Module | 28V / 55V |
| Max. Current Solar Module | 5A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Available on backorder
Cotek CX1250 Battery Charger - 12V - 50A - 230VAC
484.00 €
279.00 € Excluding VAT
345.96 € Includes VAT
279.00 € Excluding VAT
345.96 € Includes VAT
Cotek CX1250 Battery Charger - 12V - 50A - 230VAC
Price without VAT
In stock
Charging Regulator Victron Bluesolar PWM Duo 12 / 24-20A
91.00 €
76.00 € Excluding VAT
94.24 € Includes VAT
76.00 € Excluding VAT
94.24 € Includes VAT
Charging regulator of Victron BlueSolar PWM DUO 12 / 24V-20A includes internal temperature sensor for smooth operation of the regulator. Also with its two outputs it allows the simultaneous charging of batteries. In addition, it includes three stages of battery charging (Bulk, absortion, float), which ensure the maximum charge of the battery, which in turn ensures the smooth operation of your photovoltaic system. The BlueSolar PWM DUO 12 / 24V-20A charge regulator also includes an advanced protection system against short circuits and overvoltages as well as from reverse polarity effects of the solar panels or the battery itself.
Charging Regulator, with 2 outputs for charging Batteries
- PWM controller
- Charges two separate batteries. E.g. the starter battery or the operating battery of the boat or caravan
- Programmable charging current ratio (normal setting: equal current for both batteries)
- Charging voltage regulation of three types of batteries (Gel, AGM and Flooded)
- Internal heat sensor and optional remote control heat sensor
- It is protected from overvoltage
- It is protected against short circuits
- It is protected from reverse polarity of photovoltaic panels and / or batteries.
Price without VAT
Out of stock
10A PWM charge regulator LS1024
19.00 €
11.50 € Excluding VAT
14.26 € Includes VAT
11.50 € Excluding VAT
14.26 € Includes VAT
10A, programmable charge regulator with night mode.
Technical data - programming
| QUICK START INSTRUCTIONS | |||||||||||||||||||||||||||||||||||
| This section provides a brief overview of how to get started using the controller. However, please review the entire manual to ensure best performance and years of trouble-free service. 1. Mount the controller on a vertical surface. Allow space above and below the controller for air flow. 2. Make sure the PV and load currents will not exceed the ratings of the controller being installed. 3. It is recommended that the connections be made in order from 1 to 6. (see the following picture) |
|||||||||||||||||||||||||||||||||||
| 4. Connect the BATTERY first. Use care that bare wires do not touch the metal case of the controller. 5. Connect the SOLAR (PV array) next. The green LED indicator will light if sunlight is present. 6. Connect the LIGHT last. If the red LED indicator lights, the battery capacity is low and should be charged before completing the system installation 7. Press the BUTTON as 6 or 7 to verify the system connection. |
|||||||||||||||||||||||||||||||||||
| 3. Connect the consumer to the charge regulator - plus and minus Please observe that the automatic adjustment to 12V / 24V systems does not function properly, if this sequence order is not followed. An improper sequence order can damage the battery! | |||||||||||||||||||||||||||||||||||
| LIGHTING CONTROL OPTIONS | |||||||||||||||||||||||||||||||||||
| 1. Press the power switch for 5 seconds, and select the desired LIGHTING CONTROL option. The LED is on, which confirms you have selected the right one. 2. The controller requires 10 minutes of continuous transition values before it starts to work. These constraints avoid false transitions due to lightning or dark storm clouds. 3. 10 minutes off before the controller starts to work. 4. A brief description follows below: |
|||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||
Price without VAT
Out of stock
Most viewed products
-
10kW PPC Photovoltaic ECO 545 Solar on roofs
6,800.00 €
5,300.00 € Excluding VAT
6,572.00 € Includes VAT10 Kwatt photovoltaic on roofs with interconnected to PPC photovoltaic system with installation
Photovoltaic Eco 545
See all offers here
Available on backorder
-
5kW PPC Photovoltaic ECO Solar 410-420 WATT with possibility for Installation
7,280.00 €
4,800.00 € Excluding VAT
5,952.00 € Includes VAT
410-WATT-420-WATT-
About answers to the most common questions about photovoltaics in homes. See the special offers of photovoltaics for 2022
5kw with photovoltaics on roofs with photovoltaics and installation Additional offers here
Available on backorder
-
Net metering 5kW photovoltaic package with 450 watt panels
3,650.00 €
2,750.00 € Excluding VAT
3,410.00 € Includes VATNet metering 5kW photovoltaic package offer
11 Photovoltaic panels 450 watts
Network inverter Renac NA 5000 DS (7500WATT max) 10 Year Warranty
Tile roof supports for 11 PV panels.
In stock
-
Net metering 10kW energy offset with PPC
6,700.00 €
5,590.00 € Excluding VAT
6,931.60 € Includes VATNet metering 10kW for energy offset and savings with PPC with production up to 16.600kWh per year
Available on backorder
-
Autonomous photovoltaic package 1.2kWh/24 hours-12v
599.00 €
465.00 € Excluding VAT
576.60 € Includes VATAvailable on backorder
-
Autonomous PV for a holiday home 4,5kWh with air conditioner
2,600.00 €
1,780.00 € Excluding VAT
2,207.20 € Includes VATAutonomous photovoltaic for a 4,5kWh cottage with air conditioning
Available on backorder
-
Net-metering 10kw with 10kwh lithium battery for storage with 460 WATT PV and Panels Complete package
17,800.00 €
14,100.00 € Excluding VAT
17,484.00 € Includes VATNet-metering 10kw with 10kwh lithium battery for storage with PV 460 WATT and Panels Complete AC/DC package for energy compensation (10 year inverter warranty)
Net metering 10kw with 10kwh lithium battery ( They produce in the summer in southern areas 40-50kw daily and about half or 1/3 in Winter) 12.000 - 16.000 kw averaged per year in Southern regions.
Price without VAT
Available on backorder
-
Photovoltaic Luxor 540 watt mono half cell ecoline LX-540M / 182-144-Germany
329.00 €
159.00 € Excluding VAT
197.16 € Includes VATPhotovoltaic Luxor 540 watt mono half cell ecoline LX-540M / 182-144-Germany
Suitable for net-metering, home photovoltaics, parks and photovoltaic stations
Minimum purchase quantity 9 pieces
Available on backorder
-
5 kwh- 7kwh/24v/220AC – 24V Premium Photovoltaic System
3,750.00 €
2,950.00 € Excluding VAT
3,658.00 € Includes VAT4 pcs. Φ / Β panel Solar Energy SE 270 / 270-275 watt Poly/ European. They have positive Photovoltaic system Premium 24V tolerance and power in watts. That is, they always deliver more watts than their rated power, high efficiency installed power 1080 watts up to + 5% more efficiency. Available with 12 years warranty factory equipment and 25 years warranty 80% yield.
1 pc. pure sine wave inverter Phoenix 24/1600 3200 watt power supply high reliability. Suitable for operation of all devices of corresponding power. Provides energy savings of up to 25% on self-consumption due to stabilized sine. Warranty 60 months (5 years)
4 pcs. Batteries S. Energy ECOAGM 220 / 250AH C100 type VRLA/ AGM corresponding specifications to GEL batteries. (deep closed type discharge lasting 10-12 years of life). Total 828AH / 12V
Possibility to add 2V High-strength and longer-lasting batteries in extreme uses at a small additional cost.
1 pc. Charging regulator Phocos CXN 40 (Digital programmable) (2 years warranty)
Ability to add MPPT controller with datalogger to increase efficiency up to 25% at a small additional cost.
Available on backorder
-
5kw Mitsubishi Electric
7,280.00 €
5,200.00 € Excluding VAT
6,448.00 € Includes VAT5kw with photovoltaic Mitsubishi PV (250W) 250 watts polycrystalline silicon
It produces an average of 6500kw per year (for areas of Attica and further south) while covering an area of 35-40 square meters on a pergola or 60-80 square meters on a terrace. It saves 800-1000 euros per year and absorbs the installation cost in 5.5 - 6.5 years.
Price without VAT
Out of stock
Recently viewed products
-
3.5KW-Pure Sine Hybrid Inverter / 3500W 24V & Charge Controller 30-80A China
891.00 €
514.00 € Excluding VAT
637.36 € Includes VAT3.5KW-Pure Sine Hybrid Inverter 3.5kw/3500W 24V & Charge Controller 30-80A China
In stock
-
10Kw-Solaredge SE SE10K SETAPP grid inverter for photovoltaics
2,360.00 €
1,859.00 € Excluding VAT
2,305.16 € Includes VATSolaredge SE SE10K SETAPP network inverter for photovoltaics. Suitable inverter for net metering, photovoltaic on roofs, home and professional photovoltaic systems.
Available on backorder
-
Blue Power IP22 Charger 12/20 Battery Charger (3 Outputs)
180.00 €
151.00 € Excluding VAT
187.24 € Includes VATThe highest performance ever achieved!
With up to 94% efficiency, the heat loss of these chargers is three to four times lower than the industry specifications. In addition, once the battery is fully charged, power consumption is automatically reduced below 0.5 Watt, a value about five to ten times lower than the industry standard, a feature that makes this charging range one of the best and most reliable on the market.
Price without VAT
Available on backorder
-
Blue Power IP67 Charger 24/8 Battery Charger (1 'Output + Si)
174.00 €
147.00 € Excluding VAT
182.28 € Includes VATCharger Blue Power IP 67 fully protected: waterproof, with protection against vibration and ignition
The Blue Power IP67 charger is not at risk from water, oil or dirt. The housing is made of cast aluminum and the electronic components are made of resin molds.Price without VAT -
150AH Solar Semi Traction Deep discharge batteries Super heavy duty
219.00 €
179.00 € Excluding VAT
221.96 € Includes VAT -
Studer HPC 8000-48
5,338.00 €
3,769.00 € Excluding VAT
4,673.56 € Includes VAT8000VA 48V with battery charger and switch relay / 30 min
Studer converters with integrated Compact series battery-charger
Compact series inverters come with 3 devices - a sinusoidal inverter, a battery charger and a transfer system.Price without VAT
Available on backorder
-
15w / 12v lamp
10.50 €
8.90 € Excluding VAT
11.04 € Includes VAT15watt / 12v economy type efficiency 75 watt incandescent lamp
CFL PHOCOS 'lamps with 15 W and 30 W Power consumption open a new range for 12 V DC lighting equipment. The lamp life is more than 8.000 hours. The new version of CFLs is now regulated by a DC-preheating circuit which makes for an extremely high number of cycles (IEC925).
Price without VAT
In stock
-
Photovoltaic standalone 1.30kwh-1.55kwh12V /220V AC standard
740.00 €
629.00 € Excluding VAT
779.96 € Includes VAT1.35KWh to 1.50KWh with operating voltage 12v DC / 220VAC. Produced energy 24 hours a day during the summer months.
Price without VAT.
Available on backorder
-
ECO MPPT ES 100V / 20A charge regulator
109.00 €
79.90 € Excluding VAT
99.08 € Includes VATECO MPPT ES 100V / 20A charge regulator with the possibility of increasing the efficiency up to 30%
Charging regulators ECO MPPT ES 150 / 20A for autonomous photovoltaic systems have a smart algorithm for detecting the maximum power point of the photovoltaic depending on the sunshine and the temperature, thus maximizing the efficiency of the system up to 30%. Suitable for all types of polycrystalline and monocrystalline silicon panels.
They are real MPPT charge regulators with an open input voltage of 150V at 30Α and not a low voltage MPPT-PWM false
They have a digital operating screen and a built-in datalogger
Circuit protections:
· Short circuit protection on the photovoltaic side.
· Discharge protection.
· Overload protection.
· Overload protection.
· Short circuit protection in loads.
· Protection against reverse polarity of photovoltaics.
· Protection against incorrect battery polarity connection.In stock
-
STUDER XTM 4000-48
2,799.00 €
1,999.00 € Excluding VAT
2,478.76 € Includes VAT4000 VA 48 Vdc 230 Vac / 50 Hz with switching system and integrated 65A battery charger.
Studer Xtender
The Studer Xtender converter is the ideal solution for complex hybrid systems. It can be adapted and connected to PV panels, small wind turbines, diesel generators and even the public electricity grid, regardless of whether it operates as a single-phase or three-phase converter.Price without VAT
Available on backorder
