Renewable Energy> Photovoltaic-Batteries-Inverters-Regulators
Open Sidebar
-39%LimitedSOLD OUT
solar-charger-rythistis-fortisis-10a-ls1024-pwm.jpg
Add to Compare Added to Compare

10A PWM charge regulator LS1024

Cotek CX1250 Battery Charger - 12V - 50A - 230VAC

279.00 € + VAT

20A Solar Charger PWM LS2024

13.50 € + VAT
19.00 €
11.50 € Excluding VAT
14.26 € Includes VAT

10A, programmable charge regulator with night mode.

 Technical data - programming

QUICK START INSTRUCTIONS  
This section provides a brief overview of how to get started using the controller. However, please review the entire manual to ensure best performance and years of trouble-free service. 
1. Mount the controller on a vertical surface. Allow space above and below the controller for air flow. 
2. Make sure the PV and load currents will not exceed the ratings of the controller being installed. 
3. It is recommended that the connections be made in order from 1 to 6. (see the following picture)
 
4. Connect the BATTERY first. Use care that bare wires do not touch the metal case of the controller. 
5. Connect the SOLAR (PV array) next. The green LED indicator will light if sunlight is present. 
6. Connect the LIGHT last. If the red LED indicator lights, the battery capacity is low and should be charged before completing the system installation 
7. Press the BUTTON as 6 or 7 to verify the system connection.
3. Connect the consumer to the charge regulator - plus and minus Please observe that the automatic adjustment to 12V / 24V systems does not function properly, if this sequence order is not followed. An improper sequence order can damage the battery!
LIGHTING CONTROL OPTIONS
1. Press the power switch for 5 seconds, and select the desired LIGHTING CONTROL option. The LED is on, which confirms you have selected the right one. 
2. The controller requires 10 minutes of continuous transition values ​​before it starts to work. These constraints avoid false transitions due to lightning or dark storm clouds. 
3. 10 minutes off before the controller starts to work. 
4. A brief description follows below:
　0,1,2,3,4,5,6,7 　For DC output
　0 　Dusk-to-Dawn, light is on all light
　1 　1 hours light is turned on after sunset
　2 　2 hours light is turned on after sunset
　3 　3 hours light is turned on after sunset
　4 　4 hours light is turned on after sunset
　5 　5 hours light is turned on after sunset
　6 　6 hours light is turned on after sunset
　7 　7 hours light is turned on after sunset
　0. 　8 hours light is turned on after sunset
　1. 　9 hours light is turned on after sunset
　2. 　10 hours light is turned on after sunset
　3. 　11 hours light is turned on after sunset
　4. 　12 hours light is turned on after sunset
　5. 　13 hours light is turned on after sunset
　6. 　Lights remain turned off, ON / OFF mode
　7. 　Test mode, lights on after it detects no light, lights off after it detects light.

 

Price without VAT

Out of stock

  ... people are viewing this right now
  Share

The 10A, programmable charge controller with night mode in black or white. It has a PWM microprocessor for more efficient and smoother charging. Also programmable for Night mode. It has a light sensor and a timer. It includes connectors for devices that are programmed to operate at night while at the same time they are switched off according to the respective programming.

 Technical data - programming

QUICK START INSTRUCTIONS  
This section provides a brief overview of how to get started using the controller. However, please review the entire manual to ensure best performance and years of trouble-free service. 
1. Mount the controller on a vertical surface. Allow space above and below the controller for air flow. 
2. Make sure the PV and load currents will not exceed the ratings of the controller being installed. 
3. It is recommended that the connections be made in order from 1 to 6. (see the following picture)
 
4. Connect the BATTERY first. Use care that bare wires do not touch the metal case of the controller. 
5. Connect the SOLAR (PV array) next. The green LED indicator will light if sunlight is present. 
6. Connect the LIGHT last. If the red LED indicator lights, the battery capacity is low and should be charged before completing the system installation 
7. Press the BUTTON as 6 or 7 to verify the system connection.
3. Connect the consumer to the charge regulator - plus and minus Please observe that the automatic adjustment to 12V / 24V systems does not function properly, if this sequence order is not followed. An improper sequence order can damage the battery!
LIGHTING CONTROL OPTIONS
1. Press the power switch for 5 seconds, and select the desired LIGHTING CONTROL option. The LED is on, which confirms you have selected the right one. 
2. The controller requires 10 minutes of continuous transition values ​​before it starts to work. These constraints avoid false transitions due to lightning or dark storm clouds. 
3. 10 minutes off before the controller starts to work. 
4. A brief description follows below:
　0,1,2,3,4,5,6,7 　For DC output
　0 　Dusk-to-Dawn, light is on all light
　1 　1 hours light is turned on after sunset
　2 　2 hours light is turned on after sunset
　3 　3 hours light is turned on after sunset
　4 　4 hours light is turned on after sunset
　5 　5 hours light is turned on after sunset
　6 　6 hours light is turned on after sunset
　7 　7 hours light is turned on after sunset
　0. 　8 hours light is turned on after sunset
　1. 　9 hours light is turned on after sunset
　2. 　10 hours light is turned on after sunset
　3. 　11 hours light is turned on after sunset
　4. 　12 hours light is turned on after sunset
　5. 　13 hours light is turned on after sunset
　6. 　Lights remain turned off, ON / OFF mode
　7. 　Test mode, lights on after it detects no light, lights off after it detects light.

 

Price without VAT

Weight 1 kg
Brand

SKU: 10A PWM charge regulator LS1024 Categories: , , , , ,

you may also like...

-16%Limited
Add to cart
Victron BlueSolar
Victron BlueSolar PWM PRO 12 / 24V-20A - PWM Charging Regulator (12 / 24V) 20A for Photovoltaics 51.00 €
43.00 € Excluding VAT
53.32 € Includes VAT

Victron BlueSolar PWM PRO 12 / 24V-20A - PWM Charging Regulator (12 / 24V) 20A for Photovoltaics

The BlueSolar PWM-Pro series with default operating settings is one of the most advantageous and reliable solutions on the market. The charge regulator BlueSolar PWM-Pro 12 / 24V-20A has three battery charging stages (Bulk, absortion, float) which maximizes the battery life and the smooth operation of your photovoltaic system. It also has protection against short circuits and overvoltages as well as from reverse polarity phenomena of solar panels or the battery. It can also be programmed with the help of the integrated BlueSolar Pro remote control panel easily, quickly and correctly.

Programmable with night mode

  1. The BlueSolar PWM-Pro 12 / 24V-20A charge controller is ready to use with its default settings. It is also fully programmable with the help of the BlueSolar Pro Remote Panel
  2. Three stages of battery charging (programmed with the help of BlueSolar Pro Remote Panel)
  3. Battery status check function (Remote Panel required)
  4. Night mode (Remote Panel required)
  5. Load output with battery discharge protection, overload protection and short circuit.
  6. Reverse polarity protection of photovoltaic - battery.
  7. Optional external temperature sensor.

 Specifications

 

Manufacturer VictronEnergy
Charge Controller Type PWM
System Voltage 12V, 24V
Connectivity Fananzeige Pro Fanbedienpanel, PWM-Pro with USB Interface Cable, Temperature Turbines
Permitted Humidity max. 98% (not condensing)
IP Protection IP30
Charging Current max. 20A
Standby Self-Consumption 10mA
Max. Voltage Solar Module 28V / 55V
Max. Current Solar Module 20A
Number of Charging Outputs 1
Ambient Temperature -20 ° C - + 50 ° C

 

Available on backorder

-14%Limited
Add to cart
Victron BlueSolar PWM PRO 10A
Victron BlueSolar PWM PRO 10A 29.00 €
25.00 € Excluding VAT
31.00 € Includes VAT

Victron BlueSolar PWM PRO 12 / 24V-10A - PWM Charging Regulator (12 / 24V) 10A for Photovoltaics

The BlueSolar PWM-Pro series is ready to use with the default settings. It has three stages of battery charging (Bulk, absortion, float), protection against short circuit and over-voltages as well as from reverse polarity of the solar panels and / or the battery. These unique features make the BlueSolar PWM -Pro 12 / 24V-10A controller one of the most valuable controllers on the market. It can also be programmed easily, quickly and correctly with the help of the integrated BlueSolar Pro remote control panel.

Specifications 

Manufacturer VictronEnergy
Charge Controller Type PWM
System Voltage 12V, 24V
Connectivity Fananzeige Pro Fanbedienpanel, PWM-Pro with USB Interface Cable, Temperature Turbines
Permitted Humidity max. 98% (not condensing)
IP Protection IP30
Charging Current max. 10A
Standby Self-Consumption 10mA
Max. Voltage Solar Module 28V / 55V
Max. Current Solar Module 10A
Number of Charging Outputs 1
Ambient Temperature -20 ° C - + 50 ° C

Price without VAT

Available on backorder

-48%LimitedSOLD OUT
read more
LS2024EU 20A PWM-USB Charging regulator 28.00 €
14.50 € Excluding VAT
17.98 € Includes VAT

LS2024EU 20A PWM charge controller with USB

Ο charge regulator LS2024EU 20A with USB output provides efficient charging by applying the new PWM technology, increasing the battery life and improving the performance of the photovoltaic panels of a system; Load output · Provides battery temperature compensation ensuring proper charging and discharging of parameters automatically.

Features Electronic protection: · Load overload protection · Short circuit protection · Over-discharge battery protection · Reverse battery polarity protection

Price without VAT

Out of stock

-15%Limited
Add to cart
Bluesolar PWM Light 48V-30A
Victron BlueSolar PWM Light 48V / 30A - PWM 30A Charging Regulator for Photovoltaics 66.00 €
56.00 € Excluding VAT
69.44 € Includes VAT

Victron BlueSolar PWM Light 48V-30A - PWM 30A Charging Regulator for Photovoltaics

The charging regulator Victron Victron Bluesolar PWM Light 48V-30A, has an internal temperature sensor and consists of an advanced system of three stages of battery charging (Bulk, absortion, float) that ensures the correct charging process of your battery is charged resulting in maximizing life her! It is a very reliable charge regulator with protection against short circuits and overvoltages as well as from reverse polarity phenomena of solar panels and / or the battery. The charge regulator Victron Victron Bluesolar PWM Light 48V-30A is suitable for photovoltaic systems, for charging the batteries with current up to 30A.

Specifications

Manufacturer VictronEnergy
Charge Controller Type PWM
System Voltage 48V
Permitted Humidity max. 95% RF (not condensing)
IP Protection IP20
Charging Current max. 30A
Standby Self-Consumption 10mA
Max. Voltage Solar Module 100V
Max. Current Solar Module 30A
Number of Charging Outputs 1
Ambient Temperature -20 ° C - + 50 ° C

Available on backorder

Related products

-23%Limited
Add to cart
Cotek CX2440 Battery Charger - 24V - 40A - 230VAC 495.00 €
379.00 € Excluding VAT
469.96 € Includes VAT

Cotek CX2440 Battery Charger - 24V - 40A - 230VAC 

Price without VAT

In stock

-16%Limited
Add to cart
Victron BlueSolar PWM
Victron BlueSolar PWM Light 12 / 24V-30A - PWM 30A Charging Regulator for Photovoltaics 44.00 €
37.00 € Excluding VAT
45.88 € Includes VAT

Victron BlueSolar PWM Light 12 / 24V-30A - PWM 30A Charging Regulator for Photovoltaics

Charging regulator of Victron BlueSolar PWM Light 12 / 24V-30A includes internal temperature sensor. It consists of three stages of battery charging (Bulk, abortion, float), has an advanced protection system against short circuits and over-voltages.

Specifications : 

  • Battery Voltage: 12 / 24V (Automatic selection)
  • Night mode (details in the Remote Panel manual)
  • Rated charging current: 30 A
  • Second battery output: not available
  • Automatic load disconnection: Yes (maximum load 30A)
  • Maximum input voltage of PV panel: 28V / 55V
  • Self-consumption: <10mA
  • Protection: battery reverse polarity, short circuit, overheating
  • Operating temperature range -20 to +50 C
  • Absorption charge (default): 14.4V (12V) / 28.8V (24V)
  • Float charge (default): 13.8V (12V) / 27.6V (24V)
  • Equalization charge (default): 14.6V (12V) / 29.2V (24V)
  • Load disconnection voltage (default): 11.1V (12V) / 22.2V (24V)
  • Load reconnection voltage (default): 12.6V (12V) / 25.2V (24V)
  • Protection class (dust-humidity): IP 30
  • Dimensions: 138x70x37 mm
  • Warranty: 5 Years

Available on backorder

-20%Limited
Add to cart
Cotek CX2425 Battery Charger - 24V - 25A - 230VAC 349.00 €
279.00 € Excluding VAT
345.96 € Includes VAT

Cotek CX2425 Battery Charger - 24V - 25A - 230VAC 

Price without VAT

In stock

-20%LimitedSOLD OUT
read more
Waterproof charging regulator LS1024EPD 10A PWM 25.00 €
20.00 € Excluding VAT
24.80 € Includes VAT

Waterproof / watertight charge regulator IP 67  LS1024EPD 10A  PWM technology. Suitable for lighting columns, garden lights, yachts, yachts and generally for outdoor use with protection from moisture.

Price without VAT

Out of stock

-8%LimitedSOLD OUT
read more
Charging regulator VS6024BN 60A PWM-USB 129.00 €
119.00 € Excluding VAT
147.56 € Includes VAT

Charging regulator VS6024BN 60A PWM with programmable screen

Suitable for charging the batteries with current up to 60A (ie with photovoltaic panels with a total power of 1.500Wp at 24V or 750Wp at 12V). It also has a socket for connecting devices, with their automatic shutdown before the battery is completely discharged, thus protecting it from premature wear. The regulator stops charging automatically when the batteries charge.

It has digital screen with indications of the charging status and voltage of the batteries or the output of the panels in Ampere and the possibility of adjusting the charging voltage of the batteries. Shows the battery charge rate, what is the operating voltage while fully programmed.

Price without VAT

Out of stock

-29%Limited
Add to cart
LS2024EPD 20A PWM Charging regulator waterproof 42.00 €
29.90 € Excluding VAT
37.08 € Includes VAT

Waterproof / watertight charge regulator IP 67  LS2024EPD 20A  PWM technology. Suitable for lighting columns, garden lights, yachts, yachts and generally for outdoor use with protection from moisture.

Price without VAT

In stock

-42%Limited
Add to cart
Cotek CX1250 Battery Charger - 12V - 50A - 230VAC 484.00 €
279.00 € Excluding VAT
345.96 € Includes VAT

Cotek CX1250 Battery Charger - 12V - 50A - 230VAC
Price without VAT

In stock

-31%LimitedSOLD OUT
read more
Charging regulator LS1024EU 10A PWM-USB 18.00 €
12.40 € Excluding VAT
15.38 € Includes VAT

Ο charge regulator LS1024EU 10 provides efficient charging by applying the new PWM technology increasing the battery life and improving the performance of the photovoltaic panels of a system · Has MOSFET as electronic switch, without mechanical switch · Provides LED indicators that inform about the voltage status of the battery · Provides control Load output · Provides battery temperature compensation ensuring proper charging and discharging of parameters automatically.

Features Electronic protection: · Load overload protection · Short circuit protection · Over-discharge battery protection · Reverse battery polarity protection

Price without VAT

Out of stock

-44%LimitedSOLD OUT
read more
Phocos CXN 40 40A digital charge regulator
Phocos CXN 40 40A digital charge regulator 129.00 €
72.00 € Excluding VAT
89.28 € Includes VAT

 Phocos CXN 40 40A digital charge regulator

Price without VAT

Out of stock

-55%LimitedSOLD OUT
read more
Charging regulator LS0512EU 5A PWM 19.00 €
8.50 € Excluding VAT
10.54 € Includes VAT

Charging regulator LS0512EU 5A PWM with USB output

 Specifications:

Ο charge regulator LS0512EU 5A provides efficient charging by applying the new PWM technology, increasing battery life and improving the performance of a system's photovoltaic panels; of the load output · Provides compensation of the temperature of the batteries ensuring proper charging and discharging of the parameters automatically

It has Electronic protection:

· Load overload protection · Short circuit protection · Battery protection against overcharging · Reverse battery polarity protection

Price without VAT

Out of stock

-44%Limited
Add to cart
WATERPROOF CHARGING REGULATOR LS1024BP 57.00 €
32.00 € Excluding VAT
39.68 € Includes VAT

Charging regulator  waterproof / waterproof LS1024BP 10A PWM with aluminum body IP67. Suitable for outdoor use or operation facing the sea. Ideal for outdoor garden lights, light columns, yachts, caravans, caravans

Price without VAT

In stock

-22%Limited
Add to cart
CHARGING REGULATOR PHOCOS CX-10 12V-24V-10A 37.00 €
29.00 € Excluding VAT
35.96 € Includes VAT

System voltage: 12V / 24V automatic selection. Maximum charging / load current: 10A / 10A Same consumption: operating temperature: -20 ~ + 50⁰C Dimensions: 92 x 93 x 38 mm Weight: 168gr Protection: IP22

Price without VAT

In stock

Most viewed products

Recently viewed products

  • -17%LimitedSOLD OUT
    read more
    24V-autonomous-5.9kwh- 6.9kwh / 24v / 220AC - 24V Photovoltaic System Europe Premium
    6.5kwh- 7.5kwh / 24v / 220AC - 24V Europe Premium Photovoltaic System (5 year warranty *) 3,500.00 €
    2,890.00 € Excluding VAT
    3,583.60 € Includes VAT

    6.5kwh-7.5kwh / 24v / 220AC - 24V Europe Premium Photovoltaic System (5 year warranty *)

    24V Photovoltaics Europe Premium with deep discharge batteries and life expectancy of 10-12 years

    System analysis 6.5kwh-7.5kwh (24 hours a day during the summer months).

    For a similar performance in Winter, double panels or a 450-500 wind turbine are required. watt

    Appliances: Energy class A refrigerator Medium, ECO Medium Washing Machine (up to 1200watt) + Lighting + 8 lamps + TV + small appliances 550wh

    4 pcs. Φ/Β panel Solar Energy SE 330 / 330-335 watts Poly / European. 

    4 pcs. Batteries S. Energy ECOGEL 250 (250AH C20 / 280AH C100) type GEL batteries. (1250 cycles DOD 50%) 

    1 pc. pure sine wave inverter Phoenix Inverter C 24/2000

    2 pcs. Charging regulator ECO ES 150 / 30A  programmable 150V with digital display (2 year warranty).

    Photovoltaic support bases

    Price without VAT

    Out of stock

  • -31%Limited
    Add to cart
    Sharp NE-80E2E 99.00 €
    68.00 € Excluding VAT
    84.32 € Includes VAT

    80 Wp polycrystalline silicon

    Price without VAT


    In stock

  • -22%Limited
    Add to cart
    10 OPzV 1000 2V GEL 483.00 €
    379.00 € Excluding VAT
    469.96 € Includes VAT

    1105AH - 1550AH in a charging cycle C10 hours and C120 hours, GEL battery deep discharge

    The OPzV series consists of closed-type lead elements that combine proven gel and tubular plate technologies to offer high levels of reliability and performance.

    Price without VAT

  • -29%Limited
    Add to cart
    LS2024EPD 20A PWM Charging regulator waterproof 42.00 €
    29.90 € Excluding VAT
    37.08 € Includes VAT

    Waterproof / watertight charge regulator IP 67  LS2024EPD 20A  PWM technology. Suitable for lighting columns, garden lights, yachts, yachts and generally for outdoor use with protection from moisture.

    Price without VAT

    In stock

  • -23%Limited
    Add to cart
    Photovoltaic autonomous 0.50KWh_12V / 220V / AC 440.00 €
    338.00 € Excluding VAT
    419.12 € Includes VAT

    0.50kWh to 0.60kWh with operating voltage 12v DC / 220VAC. Produced energy 24 hours a day during the summer months.

    Available on backorder

  • -32%Limited
    Add to cart
    Huawei SUN2000 10KTL M1-10k W Inverter Photovoltaic Three-phase-photovoltaic, net metering, photovoltaic on the roof, home
    Huawei SUN2000 10KTL M1-10k W Three Phase Photovoltaic Inverter 2,360.00 €
    1,615.00 € Excluding VAT
    2,002.60 € Includes VAT

    Huawei SUN2000 10KTL M1-10k W Three Phase Photovoltaic Inverter. Suitable inverter for net metering, photovoltaic on roofs, home and professional photovoltaic systems.

    Available on backorder

  • -49%Limited
    Add to cart
    SET Photovoltaic Panel Mono 545W 31 pieces V-TAC 1135431
    SET Photovoltaic Panel Mono 545W 31 pieces V-TAC 1135431 8,200.00 €
    4,185.00 € Excluding VAT
    5,189.40 € Includes VAT

    SET Photovoltaic Panel Mono 545W 31 pieces V-TAC 1135431

    Output 545W

    Dimensions 1722 x 1134 x 35mm

    Minimum SET purchase quantity 

    In stock

  • -20%Limited
    Add to cart
    Goodwe GW2000-XS 500V-inverter-timh-Greece-agora
    Goodwe GW2000-XS 500V 488.00 €
    392.00 € Excluding VAT
    486.08 € Includes VAT

    Goodwe GW2000-XS 500V

    Network Inverter 2500 watts up to 2750 watts

    Available on backorder

  • -15%Limited
    Add to cart
    Skylla-TG Battery Charger 24/100 (1 + 1) 120-240V 1,846.00 €
    1,560.00 € Excluding VAT
    1,934.40 € Includes VAT

    A full output output and a 4 Amp output. The charging voltage can be precisely adjusted to adjust

    on any battery system. The input for the charger is 230V at 50 / 60HZ. To compensate for the voltage loss due to

    resistance of the cable, the charging voltage can be measured directly at the battery terminal. An external sensor

    allows the charging voltage to be reduced when the battery temperature rises.

    Available on backorder

  • -16%Limited
    Add to cart
    Victron BlueSolar PWM Charge
    Victron BlueSolar PWM Charge Controller-LCD and USB 12 / 24V / 20A 20A charge regulator 50.00 €
    42.00 € Excluding VAT
    52.08 € Includes VAT

    Victron BlueSolar PWM Charge Controller-LCD and USB 12 / 24V / 20A Solar Charge Controller 20A Digital with Liquid Crystal Display for Photovoltaic Panels

    Available on backorder

PWM Solar Charger 10A, charge regulator,

PWM Solar Charger 10A, charge regulator,

Regulator Programmable with night mode - PWM Solar Charger 10A, has a light sensor and timer, prices

My cart
Close Wishlist
Close Recently Viewed
Compare Products (0 Products)
Compare Products
Compare Products
Compare Products
Compare Products
Clear All Let's Compare!
Category