7 results
-
Lorentz etatrack 400
705.00 €
529.00 € Excluding VAT
655.96 € Includes VAT4 square meters covered area
Price without VAT
Out of stock
-
Lorentz PS600 BADU
1,277.00 €
999.00 € Excluding VAT
1,238.76 € Includes VATPump with controller
survey
centrifugal pump surface for solar operation
flow rate up to 15 m3 / h
simple installation
maintenance-free thanks to the brushless DC motor
high reliability and life expectancy
cost-effective pumping
2-year manufacturer's warranty against defects in material and workmanship
Applications
pool water circulation through a filter system and thermal collectors
management pond
irrigation
aquariums
etc.
Pump end (PE) Top BADU 12
monoblock type pump with integrated strainer tank
under mechanical seal is mounted on a plastic shaft protected sleeve
motor / shaft pump has no contact with the fluid
total electrical separation
strainer about capacity. 3 L
strainer basket size approx. 3,2 x 2,6 mm
The material used for the end of the pump
pump housing, strainer basket: PP
flange, housing gland: PP TV 40
diffuser: PP TV 40
impeller: PA 66 GF 30 / PC
lid: PC, transparent
mechanical seal: carbon / ceramic / NBR
screws: steel, galvanized
Engine ECdrive 600 BADU Top
brushless, DC motor maintenance
Controller PS600
control of the pump system and monitoring of operating conditions
mounted on the surface (not immersed electronics)
two control inputs for better pumping (protection against dry operation), float or pressure switches, remote control, etc.
automatic reset 20 minutes later and catheter turns pump
are protected from reverse polarity, overload and high temperature
speed control, max. pump speed adjustable to reduce the flow rate approx. 30%
Solar Power: Integrated MPPT (Maximum Power Point Tracking)
Battery operation: low voltage disconnect and restart when the battery recovers
max. 92% efficiency (engine + controller)
Price without VAT
Available on backorder
-
Lorentz PS150 Boost
1,270.00 €
1,089.00 € Excluding VAT
1,350.36 € Includes VATPump with controler
Construction & features
Rotary blade mechanism (positive displacement) from forged
brass, carbon-graphite and stainless steel
Tighten the assembly to prevent alignment problems
Handles seawater, dissolved metals
Withstands a lot of freezes
Brushless DC motor (maintenance free) is the same for 12 and 24V
application with the same flow rates
MPP tracking, the existing amplifier for direct solar applications,
Speed control pump, low voltage for the battery Disconnect
protection, Float terminal / remote control switch and low tide
catheter
Installation and Service Manual is extremely detailed and
is displayed
Suction capacity
5 meters vertically (20 ft), at sea level. Subtract 1 m for each
1.000 m altitude. Pump should be placed as low as possible and as close as possible
as much as possible in the water source. Absorbent capacity to me
less than intake pipe friction (or clogged filter) Intake
piping should be 1 inch or larger
Filter requirement
This pump can not tolerate dirt. The water must be purified.
If the water is very dirty, improve the source or consider a different one
pump
PV-Direct (without battery) Requirements
The rated power of the photovoltaic generator must exceed the pump watts
20% or more
A linear current MPPT incl (maximum power point)
monitoring) has already been included
Solar Tracker (optional) will increase daily output (40-55% on
the summer)
installation
The pump can be mounted horizontally or vertically.
The pump must not be submerged
Can be mounted inside 120 cm or larger housing,
suspended by a rope
accessory
Inline Filter: (10 “) Uses standard filter parts
Installation kit includes: pressure switch, pressure gauge,
control, drain and shut-off valves and TEE tank
Float switch for tank closed if full
Well Drought protection sensor of the pump
Dimensions
Pump unit length 33 cm
Βάρος: 7 kg
Controller 260 x 175 x 100 mm
Βάρος: 1,5 kg
warranty
1 year from defects in materials and construction
Price without VAT
Available on backorder
-
Lorentz PS 200
1,526.00 €
1,290.00 € Excluding VAT
1,599.60 € Includes VATPump with controller
Drop Pipe
11/4 ", 11/2" or 2 "at the NPT pump output. If the water is dirty, consider a smaller pipe size drop to increase the flow rate. This helps deplete solid particles and prevent them from accumulating in the pipe. When considering reduced tube size, consult a tube size (friction loss) graph. Pipe can be made of any standard material, rigid or flexible. A torque extractor is not required.
Price without VAT
Available on backorder
-
Lorentz PS 1800
1,990.00 €
1,690.00 € Excluding VAT
2,095.60 € Includes VATPump with Controller
survey
lift up to 50 m
flow rate up to 22 m3 / h
simple installation
without maintenance
high reliability and life expectancy
cost-effective pumping
2-year manufacturer's warranty against defects in material and workmanship
Applications
drinking water supply
watering the animals
management pond
irrigation
etc.
Controller PS1800
control of the pump system and monitoring of operating conditions
mounted on the surface (not immersed electronics)
two control inputs for better pumping (protection against dry operation), float or pressure switches, remote control, etc.
automatic reset 20 minutes later and catheter turns pump
are protected from reverse polarity, overload and high temperature
speed control, max. pump speed adjustable to reduce the flow rate approx. 30%
Solar Power: Integrated MPPT (Maximum Power Point Tracking)
Battery operation: low voltage disconnect and restart when the battery recovers
max. 92% efficiency (engine + controller)
housing: IP 54 (sealed, weather resistant)
Engine ECdrive 1200 C
brushless DC motor
there are no electronic parts of the motor
filled with water
IP68, balanced pressure, unlimited immersion
dynamic sliding bearings, material: carbon / ceramic
Wet material: stainless steel (AISI 316), POM, rubber, approved drinking water cable
Pump tip (PE)
high life expectancy
no-valve
protection against dry operation (optional)
Material: stainless steel (AISI 316), rubber
Price without VAT
Available on backorder
-
Lorentz PS 1200
1,990.00 €
1,690.00 € Excluding VAT
2,095.60 € Includes VATPump with controller
Drop Pipe
11/4 ", 11/2" or 2 "NPT pump output. If the water is dirty, consider a smaller drop pipe size to increase the flow rate. This helps evaporate solid particles and prevent them from accumulating in the pipe. When considering reduced pipe size, consult a pipe size (friction damage) graph. pipe can be of any standard material, rigid or flexible. A torque extractor is not required.
Price without VAT.
Available on backorder
-
Lorentz PS600 HR Submersible pump
2,300.00 €
1,990.00 € Excluding VAT
2,467.60 € Includes VATPump with controller
Drop Pipe
11/4 ", 11/2" or 2 "at the NPT pump output. If the water is dirty, consider a smaller pipe size drop to increase the flow rate. This helps deplete solid particles and prevent them from accumulating in the pipe. When considering reduced tube size, consult a tube size (friction loss) graph. Pipe can be made of any standard material, rigid or flexible. A torque extractor is not required.
Price without VAT
Available on backorder