Autonomous photovoltaic system for refrigerator 12V / 65watt - 75 watts
Autonomous photovoltaic kit / package for small refrigerator 65-75 watt / 12V or 220V by adding inverter
10A PWM charge regulator LS1024
11.50 € Excluding VAT
14.26 € Includes VAT
10A, programmable charge regulator with night mode.
Technical data - programming
| QUICK START INSTRUCTIONS | |||||||||||||||||||||||||||||||||||
| This section provides a brief overview of how to get started using the controller. However, please review the entire manual to ensure best performance and years of trouble-free service. 1. Mount the controller on a vertical surface. Allow space above and below the controller for air flow. 2. Make sure the PV and load currents will not exceed the ratings of the controller being installed. 3. It is recommended that the connections be made in order from 1 to 6. (see the following picture) |
|||||||||||||||||||||||||||||||||||
| 4. Connect the BATTERY first. Use care that bare wires do not touch the metal case of the controller. 5. Connect the SOLAR (PV array) next. The green LED indicator will light if sunlight is present. 6. Connect the LIGHT last. If the red LED indicator lights, the battery capacity is low and should be charged before completing the system installation 7. Press the BUTTON as 6 or 7 to verify the system connection. |
|||||||||||||||||||||||||||||||||||
| 3. Connect the consumer to the charge regulator - plus and minus Please observe that the automatic adjustment to 12V / 24V systems does not function properly, if this sequence order is not followed. An improper sequence order can damage the battery! | |||||||||||||||||||||||||||||||||||
| LIGHTING CONTROL OPTIONS | |||||||||||||||||||||||||||||||||||
| 1. Press the power switch for 5 seconds, and select the desired LIGHTING CONTROL option. The LED is on, which confirms you have selected the right one. 2. The controller requires 10 minutes of continuous transition values before it starts to work. These constraints avoid false transitions due to lightning or dark storm clouds. 3. 10 minutes off before the controller starts to work. 4. A brief description follows below: |
|||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||
Price without VAT
Out of stock
... people are viewing this right now
The 10A, programmable charge controller with night mode in black or white. It has a PWM microprocessor for more efficient and smoother charging. Also programmable for Night mode. It has a light sensor and a timer. It includes connectors for devices that are programmed to operate at night while at the same time they are switched off according to the respective programming.
Technical data - programming
| QUICK START INSTRUCTIONS | |||||||||||||||||||||||||||||||||||
| This section provides a brief overview of how to get started using the controller. However, please review the entire manual to ensure best performance and years of trouble-free service. 1. Mount the controller on a vertical surface. Allow space above and below the controller for air flow. 2. Make sure the PV and load currents will not exceed the ratings of the controller being installed. 3. It is recommended that the connections be made in order from 1 to 6. (see the following picture) |
|||||||||||||||||||||||||||||||||||
| 4. Connect the BATTERY first. Use care that bare wires do not touch the metal case of the controller. 5. Connect the SOLAR (PV array) next. The green LED indicator will light if sunlight is present. 6. Connect the LIGHT last. If the red LED indicator lights, the battery capacity is low and should be charged before completing the system installation 7. Press the BUTTON as 6 or 7 to verify the system connection. |
|||||||||||||||||||||||||||||||||||
| 3. Connect the consumer to the charge regulator - plus and minus Please observe that the automatic adjustment to 12V / 24V systems does not function properly, if this sequence order is not followed. An improper sequence order can damage the battery! | |||||||||||||||||||||||||||||||||||
| LIGHTING CONTROL OPTIONS | |||||||||||||||||||||||||||||||||||
| 1. Press the power switch for 5 seconds, and select the desired LIGHTING CONTROL option. The LED is on, which confirms you have selected the right one. 2. The controller requires 10 minutes of continuous transition values before it starts to work. These constraints avoid false transitions due to lightning or dark storm clouds. 3. 10 minutes off before the controller starts to work. 4. A brief description follows below: |
|||||||||||||||||||||||||||||||||||
|
|||||||||||||||||||||||||||||||||||
Price without VAT
| Weight | 1 kg |
|---|---|
| Brand |
you may also like...
LS2024EU 20A PWM-USB Charging regulator
28.00 €
14.50 € Excluding VAT
17.98 € Includes VAT
14.50 € Excluding VAT
17.98 € Includes VAT
LS2024EU 20A PWM charge controller with USB
Ο charge regulator LS2024EU 20A with USB output provides efficient charging by applying the new PWM technology, increasing the battery life and improving the performance of the photovoltaic panels of a system; Load output · Provides battery temperature compensation ensuring proper charging and discharging of parameters automatically.
Features Electronic protection: · Load overload protection · Short circuit protection · Over-discharge battery protection · Reverse battery polarity protection
Price without VAT
Out of stock
Victron BlueSolar PWM Light 48V / 30A - PWM 30A Charging Regulator for Photovoltaics
66.00 €
56.00 € Excluding VAT
69.44 € Includes VAT
56.00 € Excluding VAT
69.44 € Includes VAT
Victron BlueSolar PWM Light 48V-30A - PWM 30A Charging Regulator for Photovoltaics
The charging regulator Victron Victron Bluesolar PWM Light 48V-30A, has an internal temperature sensor and consists of an advanced system of three stages of battery charging (Bulk, absortion, float) that ensures the correct charging process of your battery is charged resulting in maximizing life her! It is a very reliable charge regulator with protection against short circuits and overvoltages as well as from reverse polarity phenomena of solar panels and / or the battery. The charge regulator Victron Victron Bluesolar PWM Light 48V-30A is suitable for photovoltaic systems, for charging the batteries with current up to 30A.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 48V |
| Permitted Humidity | max. 95% RF (not condensing) |
| IP Protection | IP20 |
| Charging Current max. | 30A |
| Standby Self-Consumption | 10mA |
| Max. Voltage Solar Module | 100V |
| Max. Current Solar Module | 30A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Available on backorder
Victron BlueSolar PWM PRO 12 / 24V-20A - PWM Charging Regulator (12 / 24V) 20A for Photovoltaics
51.00 €
43.00 € Excluding VAT
53.32 € Includes VAT
43.00 € Excluding VAT
53.32 € Includes VAT
Victron BlueSolar PWM PRO 12 / 24V-20A - PWM Charging Regulator (12 / 24V) 20A for Photovoltaics
The BlueSolar PWM-Pro series with default operating settings is one of the most advantageous and reliable solutions on the market. The charge regulator BlueSolar PWM-Pro 12 / 24V-20A has three battery charging stages (Bulk, absortion, float) which maximizes the battery life and the smooth operation of your photovoltaic system. It also has protection against short circuits and overvoltages as well as from reverse polarity phenomena of solar panels or the battery. It can also be programmed with the help of the integrated BlueSolar Pro remote control panel easily, quickly and correctly.
Programmable with night mode
- The BlueSolar PWM-Pro 12 / 24V-20A charge controller is ready to use with its default settings. It is also fully programmable with the help of the BlueSolar Pro Remote Panel
- Three stages of battery charging (programmed with the help of BlueSolar Pro Remote Panel)
- Battery status check function (Remote Panel required)
- Night mode (Remote Panel required)
- Load output with battery discharge protection, overload protection and short circuit.
- Reverse polarity protection of photovoltaic - battery.
- Optional external temperature sensor.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 12V, 24V |
| Connectivity | Fananzeige Pro Fanbedienpanel, PWM-Pro with USB Interface Cable, Temperature Turbines |
| Permitted Humidity | max. 98% (not condensing) |
| IP Protection | IP30 |
| Charging Current max. | 20A |
| Standby Self-Consumption | 10mA |
| Max. Voltage Solar Module | 28V / 55V |
| Max. Current Solar Module | 20A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Available on backorder
Victron BlueSolar PWM PRO 10A
29.00 €
25.00 € Excluding VAT
31.00 € Includes VAT
25.00 € Excluding VAT
31.00 € Includes VAT
Victron BlueSolar PWM PRO 12 / 24V-10A - PWM Charging Regulator (12 / 24V) 10A for Photovoltaics
The BlueSolar PWM-Pro series is ready to use with the default settings. It has three stages of battery charging (Bulk, absortion, float), protection against short circuit and over-voltages as well as from reverse polarity of the solar panels and / or the battery. These unique features make the BlueSolar PWM -Pro 12 / 24V-10A controller one of the most valuable controllers on the market. It can also be programmed easily, quickly and correctly with the help of the integrated BlueSolar Pro remote control panel.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 12V, 24V |
| Connectivity | Fananzeige Pro Fanbedienpanel, PWM-Pro with USB Interface Cable, Temperature Turbines |
| Permitted Humidity | max. 98% (not condensing) |
| IP Protection | IP30 |
| Charging Current max. | 10A |
| Standby Self-Consumption | 10mA |
| Max. Voltage Solar Module | 28V / 55V |
| Max. Current Solar Module | 10A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Price without VAT
Available on backorder
Related products
CHARGING REGULATOR PHOCOS CX-20 12 / 24V - 20A
45.00 €
37.00 € Excluding VAT
45.88 € Includes VAT
37.00 € Excluding VAT
45.88 € Includes VAT
System voltage: 12V / 24V automatic selection. Maximum charging / load current: 20A / 20A Same consumption: operating temperature: -20 ~ + 50⁰C Dimensions: 92 x 93 x 38 mm Weight: 168gr Protection: IP22
Price without VAT
In stock
Charging Regulator LS3024 30A PWM
34.10 €
27.00 € Excluding VAT
33.48 € Includes VAT
27.00 € Excluding VAT
33.48 € Includes VAT
30A continuous operation and programmable charge regulator.
Price without VAT
Out of stock
Victron BlueSolar MPPT 75/10 - Charging Regulator 10A-MPPT for Photovoltaic-Wind Turbines
48.00 €
41.00 € Excluding VAT
50.84 € Includes VAT
41.00 € Excluding VAT
50.84 € Includes VAT
Victron BlueSolar MPPT 75/10 - MPPT Charging Regulator 10A for Photovoltaic-Wind Turbines
Victron battery chargers, thanks to fast technology maximum power point (MPPT) from photovoltaic panels, even under shading conditions, promise the fastest possible charging of the batteries of the autonomous photovoltaic system, based on the safety of the equipment and ensuring the required charging voltage of the batteries for their proper and long-term proper operation.
They have extremely fast find the maximum power efficiency point (MPPT). Especially in the case of cloudy skies, or when the light intensity is constantly changing, an ultra-fast MPPT controller will improve energy efficiency by up to 30% compared to PWM charge controllers of up to 10% compared to slower MPPT controllers.
Specifications
| Type | MPPT |
| Power (W) | 145 (12V) / 290 (24V) |
| Manufacturer | VictronEnergy |
| Input voltage (V) | 75 |
| Output Voltage (V) | 12/24 |
| IP Protection | IP43 (electronic components), IP22 (connection area) |
| Weight (kg) | 0.5 |
| Warranty (years) | 5 years |
| Other Information | Color Blue (RAL 5012), 6 mm² / AWG10 (Power terminals), VE.Direct |
Available on backorder
Charging regulator LS1024EU 10A PWM-USB
18.00 €
12.40 € Excluding VAT
15.38 € Includes VAT
12.40 € Excluding VAT
15.38 € Includes VAT
Ο charge regulator LS1024EU 10 provides efficient charging by applying the new PWM technology increasing the battery life and improving the performance of the photovoltaic panels of a system · Has MOSFET as electronic switch, without mechanical switch · Provides LED indicators that inform about the voltage status of the battery · Provides control Load output · Provides battery temperature compensation ensuring proper charging and discharging of parameters automatically.
Features Electronic protection: · Load overload protection · Short circuit protection · Over-discharge battery protection · Reverse battery polarity protection
Price without VAT
Out of stock
10A Economy Charger regulator for photovoltaic systems
19.00 €
14.00 € Excluding VAT
17.36 € Includes VAT
14.00 € Excluding VAT
17.36 € Includes VAT
10A regulator Charger Economy series for small autonomous photovoltaic systems.
- 10A battery charger for photovoltaic frame 12v 160 watt
- With program number display and load connection output with night mode scheduling.
- Suitable for 12V or 24V batteries (automatic selection).
- Provides overload protection up to 130% of maximum load for 60s and 160% of maximum load for 5sec.
- Maximum input voltage 41V.
- Maximum voltage drop during charging 0,2V.
- Maximum operating current 10A.
- Warranty: 14 months.
Price without VAT
Out of stock
Victron BlueSolar PWM Light 48V / 20A - PWM 20A Charging Regulator for Photovoltaics
57.00 €
48.00 € Excluding VAT
59.52 € Includes VAT
48.00 € Excluding VAT
59.52 € Includes VAT
Victron BlueSolar PWM Light 48V / 20A - PWM 20A Charging Regulator for Photovoltaics
Victron charge regulator with internal temperature sensor. The BlueSolar PWM-Light 48V controller also includes a socket for connecting devices, automatically shutting down before the battery is completely discharged, thus protecting it from premature wear. With PWM technology system provides three-stage charging (Bulk, absortion, float). This way your battery is charged in the best way resulting in a much longer lifespan of itself and your system! Provides protection against short circuits and overvoltages as well as reverse polarity of solar panels or the battery.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 48V |
| Permitted Humidity | max. 95% RF (not condensing) |
| IP Protection | IP20 |
| Charging Current max. | 20A |
| Standby Self-Consumption | 10mA |
| Max. Voltage Solar Module | 100V |
| Max. Current Solar Module | 20A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Available on backorder
CHARGING REGULATOR PHOCOS CX-2048 24 / 48V - 20A
119.16 €
99.00 € Excluding VAT
122.76 € Includes VAT
99.00 € Excluding VAT
122.76 € Includes VAT
Use in small autonomous and large photovoltaic installations. The charge regulator for photovoltaics CX20-48 has an LCD graphic display, which displays the charge status of the battery and the charge, as well as the operation of the photovoltaics.
Price without VAT
In stock
Charging regulator VS6024BN 60A PWM-USB
129.00 €
119.00 € Excluding VAT
147.56 € Includes VAT
119.00 € Excluding VAT
147.56 € Includes VAT
Charging regulator VS6024BN 60A PWM with programmable screen
Suitable for charging the batteries with current up to 60A (ie with photovoltaic panels with a total power of 1.500Wp at 24V or 750Wp at 12V). It also has a socket for connecting devices, with their automatic shutdown before the battery is completely discharged, thus protecting it from premature wear. The regulator stops charging automatically when the batteries charge.
It has digital screen with indications of the charging status and voltage of the batteries or the output of the panels in Ampere and the possibility of adjusting the charging voltage of the batteries. Shows the battery charge rate, what is the operating voltage while fully programmed.
Price without VAT
Out of stock
Victron BlueSolar PWM-Light 12 / 24V-5A - PWM 5A Charging Regulator for Photovoltaics
19.00 €
16.00 € Excluding VAT
19.84 € Includes VAT
16.00 € Excluding VAT
19.84 € Includes VAT
Victron BlueSolar PWM-Light 12 / 24V-5A - PWM 5A Charging Regulator for Photovoltaics
Victron charge regulator with internal temperature sensor. It has three stages of battery charging (Bulk, absortion, float), protection against short circuit and over-voltages as well as from reverse polarity of the solar panels and / or the battery.
Programmable with night mode
- The BlueSolar PWM Light 12 / 24V-5A charge controller is ready to use with its default settings.
- Three stages of battery charging
- Battery status check function
- Night operation
- Load output with battery discharge protection, overload protection and short circuit.
- Reverse polarity protection of photovoltaic - battery.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 12V |
| Permitted Humidity | max. 95% RF (not condensing) |
| IP Protection | IP20 |
| Charging Current max. | 5A |
| Standby Self-Consumption | 10mA |
| Battery Voltage | 12V, 24V |
| Load Current max. | 5A |
| Max. Voltage Solar Module | 28V / 55V |
| Max. Current Solar Module | 5A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
Available on backorder
20A Solar Charger PWM LS2024
19.00 €
13.50 € Excluding VAT
16.74 € Includes VAT
13.50 € Excluding VAT
16.74 € Includes VAT
20A continuous operation and max 25A charge regulator programmable for use even in lighting columns, garden lights with night operation capability.
Technical analysis
Solar charge controller for street light
Dual timer function
Battery type selection
Full electronic protection
Solar charge controller
1. Intelligent system optimum controller
2. High efficient series PWM charging with temperature compensation
3. Compact size
4. Use mosfet as electronic switch, without any mechanical switch
5. Digital LED menu, only one key solve all setting simple
6. Widely used, automatically recognize day / night
7. Intelligent timer function with 1-15 hours option
8. Unique dual timer function, enhance the flexibility of street light system.
9. Gel, sealed and flooded battery type option
10. Load status display
11. Big terminals and big distance between terminals
12. Electronic protection: Overheating, over charging, over discharging, overload, and short circuit
13. Reverse polarity protection: Any combination of solar module and battery
14. Load work mode: Light on + dual timer, dusk to dawn, test, on / off
Model LS2024R
Rated Current 20A
System Voltage 12 / 24V auto work
Over Load Protection 1.25 times of rated current for 60 seconds, or 1.5 times for 5 seconds
Short Circuit Protection 3.5 times of rated current
Self-consumption Max. 6mA
Working Temperature -35'C to + 55'Cindustrial
Equalize Charging Voltage 14.6V; X2 / 24V
Boost Charging Voltage 14.4V; X2 / 24V
Float Charging Voltage 13.8V; X2 / 24V
Boost Reconnect Charging Voltage 13.2V; X2 / 24V
Temperature Compensation -30mV / 'C / 12V
Under Voltage Warning Voltage 12.0V; X2 / 24V
Low Voltage Disconnect Voltage 11.1V; X2 / 24V
Low Voltage Reconnect Voltage 12.6V; X2 / 24V
Terminals 10mm2
Enclosure IP30
| Model | LS2024R | ||
Rated Current |
20A | ||
System Voltage |
12 / 24V auto work | ||
Over Load Protection |
1.25 times of rated current for 60 seconds, or 1.5 times for 5 seconds |
||
Short Circuit Protection |
3.5 times of rated current |
||
Self-consumption |
Max. 6mA |
||
Working Temperature |
-35 ° C to + 55 ° C industrial |
||
Equalize Charging Voltage |
14.6V; x2 / 24V | ||
Boost Charging Voltage |
14.4V; x2 / 24V | ||
Float Charging Voltage |
13.8V; x2 / 24V | ||
Boost Reconnect Charging Voltage |
13.2V; x2 / 24V | ||
Temperature Compensation |
-30mV / ° C / 12V | ||
Under Voltage Warning Voltage |
12.0V; x2 / 24V | ||
Low Voltage Disconnect Voltage |
11.1V; x2 / 24V | ||
Low Voltage Reconnect Voltage |
12.6V; x2 / 24V | ||
terminals |
10 mm 2 | ||
Price without VAT |
IP30 | ||
Out of stock
Waterproof charging regulator LS1024EPD 10A PWM
25.00 €
20.00 € Excluding VAT
24.80 € Includes VAT
20.00 € Excluding VAT
24.80 € Includes VAT
Waterproof / watertight charge regulator IP 67 LS1024EPD 10A PWM technology. Suitable for lighting columns, garden lights, yachts, yachts and generally for outdoor use with protection from moisture.
Price without VAT
Out of stock
Victron BlueSolar PWM PRO 12 / 24V-30A - PWM Charging Regulator (12 / 24V) 30A for Photovoltaics
81.00 €
69.00 € Excluding VAT
85.56 € Includes VAT
69.00 € Excluding VAT
85.56 € Includes VAT
Victron BlueSolar PWM PRO 12 / 24V-30A - PWM Charging Regulator (12 / 24V) 30A for Photovoltaics
The BlueSolar PWM-Pro series is ready to use with the default settings. It has three stages of battery charging (Bulk, absortion, float), protection against short circuit and over-voltages as well as from reverse polarity of the solar panels and / or the battery. These unique features make the BlueSolar PWM -Pro 12 / 24V-10A controller one of the most valuable controllers on the market. It can also be programmed easily, quickly and correctly with the help of the integrated BlueSolar Pro remote control panel.
General characteristics:
- The BlueSolar PWM -Pro 12 / 24V-30A charge controller is ready for use with its default settings. It is also fully programmable with the help of the BlueSolar Pro Remote Panel
- Programmable with night mode
- Three stages of battery charging (programmed with the help of BlueSolar Pro Remote Panel)
- Battery status check function (Remote Panel required)
- Night mode (Remote Panel required)
- Load output with battery discharge protection, overload protection and short circuit.
- Reverse polarity protection of photovoltaic - battery.
- Optional external temperature sensor.
Specifications
| Manufacturer | VictronEnergy |
|---|---|
| Charge Controller Type | PWM |
| System Voltage | 12V, 24V |
| Connectivity | Fananzeige Pro Fanbedienpanel, PWM-Pro with USB Interface Cable, Temperature Turbines |
| Permitted Humidity | max. 98% (not condensing) |
| IP Protection | IP30 |
| Charging Current max. | 30A |
| Standby Self-Consumption | 10mA |
| Max. Voltage Solar Module | 28V / 55V |
| Max. Current Solar Module | 30A |
| Number of Charging Outputs | 1 |
| Ambient Temperature | -20 ° C - + 50 ° C |
| Supported Battery Types | Bleisäure, AGM, Gel |
Available on backorder
Most viewed products
-
10kW PPC Photovoltaic ECO 545 Solar on roofs
6,800.00 €
5,300.00 € Excluding VAT
6,572.00 € Includes VAT10 Kwatt photovoltaic on roofs with interconnected to PPC photovoltaic system with installation
Photovoltaic Eco 545
See all offers here
Available on backorder
-
5kW PPC Photovoltaic ECO Solar 410-420 WATT with possibility for Installation
7,280.00 €
4,800.00 € Excluding VAT
5,952.00 € Includes VAT
410-WATT-420-WATT-
About answers to the most common questions about photovoltaics in homes. See the special offers of photovoltaics for 2022
5kw with photovoltaics on roofs with photovoltaics and installation Additional offers here
Available on backorder
-
Net metering 5kW photovoltaic package with 450 watt panels
3,650.00 €
2,750.00 € Excluding VAT
3,410.00 € Includes VATNet metering 5kW photovoltaic package offer
11 Photovoltaic panels 450 watts
Network inverter Renac NA 5000 DS (7500WATT max) 10 Year Warranty
Tile roof supports for 11 PV panels.
In stock
-
Net metering 10kW energy offset with PPC
6,700.00 €
5,590.00 € Excluding VAT
6,931.60 € Includes VATNet metering 10kW for energy offset and savings with PPC with production up to 16.600kWh per year
Available on backorder
-
Autonomous photovoltaic package 1.2kWh/24 hours-12v
599.00 €
465.00 € Excluding VAT
576.60 € Includes VATAvailable on backorder
-
Autonomous PV for a holiday home 4,5kWh with air conditioner
2,600.00 €
1,780.00 € Excluding VAT
2,207.20 € Includes VATAutonomous photovoltaic for a 4,5kWh cottage with air conditioning
Available on backorder
-
Net-metering 10kw with 10kwh lithium battery for storage with 460 WATT PV and Panels Complete package
17,800.00 €
14,100.00 € Excluding VAT
17,484.00 € Includes VATNet-metering 10kw with 10kwh lithium battery for storage with PV 460 WATT and Panels Complete AC/DC package for energy compensation (10 year inverter warranty)
Net metering 10kw with 10kwh lithium battery ( They produce in the summer in southern areas 40-50kw daily and about half or 1/3 in Winter) 12.000 - 16.000 kw averaged per year in Southern regions.
Price without VAT
Available on backorder
-
Photovoltaic Luxor 540 watt mono half cell ecoline LX-540M / 182-144-Germany
329.00 €
159.00 € Excluding VAT
197.16 € Includes VATPhotovoltaic Luxor 540 watt mono half cell ecoline LX-540M / 182-144-Germany
Suitable for net-metering, home photovoltaics, parks and photovoltaic stations
Minimum purchase quantity 9 pieces
Available on backorder
-
5 kwh- 7kwh/24v/220AC – 24V Premium Photovoltaic System
3,750.00 €
2,950.00 € Excluding VAT
3,658.00 € Includes VAT4 pcs. Φ / Β panel Solar Energy SE 270 / 270-275 watt Poly/ European. They have positive Photovoltaic system Premium 24V tolerance and power in watts. That is, they always deliver more watts than their rated power, high efficiency installed power 1080 watts up to + 5% more efficiency. Available with 12 years warranty factory equipment and 25 years warranty 80% yield.
1 pc. pure sine wave inverter Phoenix 24/1600 3200 watt power supply high reliability. Suitable for operation of all devices of corresponding power. Provides energy savings of up to 25% on self-consumption due to stabilized sine. Warranty 60 months (5 years)
4 pcs. Batteries S. Energy ECOAGM 220 / 250AH C100 type VRLA/ AGM corresponding specifications to GEL batteries. (deep closed type discharge lasting 10-12 years of life). Total 828AH / 12V
Possibility to add 2V High-strength and longer-lasting batteries in extreme uses at a small additional cost.
1 pc. Charging regulator Phocos CXN 40 (Digital programmable) (2 years warranty)
Ability to add MPPT controller with datalogger to increase efficiency up to 25% at a small additional cost.
Available on backorder
-
Autonomous photovoltaic for caravans or cottages 0,5kWh
630.00 €
495.00 € Excluding VAT
613.80 € Includes VATAvailable on backorder
Recently viewed products
-
Bosch + 3 SMA inverters-10kw
9,960.00 €
8,800.00 € Excluding VAT
10,912.00 € Includes VATBOSCH M60 250WATT 10kw with photovoltaic panels of monocrystalline silicon. Pieces 40 with a total power of 10000 watts. The set is accompanied by
SMA inverters 2 Items Sunny Boy 3000 TL-20 & SMA 1 piece Sunny Boy 4000 TL-20 - Total power 11.000 wp.
Significant advantage for the operation of the photovoltaic system even in case of failure of one of the three phases or in case of material failure (inverter) which if a three-phase inverter is selected puts the entire PV system out of operation with significant loss of revenue until its replacement .
Price without VAT
Available on backorder
-
2 PzB 210 2V Deep discharge SUNLIGHT battery
59.00 €
54.51 € Excluding VAT
67.59 € Includes VAT2 PzB 210 2V SUNLIGHT deep discharge battery. Traction battery - open type with liquids, with 2500 cycles at 50% COMING and with excellent performance in applications that require deep discharge. Suitable for electric lifting machines - clark - clark, service on boats, autonomous photovoltaic systems and generally electric applications. SUNLIGHT traction batteries optimize your business, as they provide reliable daily power to your industrial or commercial vehicles.
Out of stock
-
WIND GENERATOR V400WATT-500WATT / MARINE 12V-24v
890.00 €
629.00 € Excluding VAT
779.96 € Includes VATThe Wind Turbine 450 Watt / 12v or 24V continuous power (12.5m / sec) 500 watt / 24v maximum power (14m / sec). It has a fully programmable external digital contoller fully programmable (worth 250 euros). Possibility for Marine use in boats or areas near the Sea.
3 year warranty.1.2 V-400 wind generator has the following advantages:
1. New design and material, long running life up to 15 years.
2. Very smart turbine, very nice design and new material.
3. Low wind start, low noise.
4. Automatic protection for strong wind.
5. Multi functional electric power controller.
6. Easy to install and uninstall.
7. Free running cost, free maintenance.
8. Excellent after sales serviceTechnical data
Rated power 450WMax power 500W
Rated wind speed 11m / s
Start up wind speed 2.5m / s
Rotor diameter 1.20m
Number of blades 3
Blade material CFRP
Body Magnalium framework
Rotor speed 500-1000rpm
GeneratorPermanent magnet, 3-phase with rectifier
Nominal voltage 12V DC or 24V DC
Brake Electromagnetic brake (over 16m / s)
Surface protection Aluminum oxide and plastic coating
Weight 7.8kg
Controller High function external controller
Price without VATOut of stock
-
410W Photovoltaic Panel V-TAC 11519 Monocrystalline half-cells
233.00 €
77.00 € Excluding VAT
95.48 € Includes VATPhotovoltaic Panel V-TAC 11519 410W Monocrystalline half-cells
Output 410W
Dimensions 1722mm x 1134mm x 30mm
Minimum purchase quantity 12 pieces
In stock
-
Bracelet made of Swarovski crystal beads
66.00 €
65.34 € Excluding VAT
81.02 € Includes VATCode: 7544
Bracelet made of Swarovski crystal beads in the shape of a cube, blue-yellow-cream glass beads and decorative metal beads, in gold-blue-yellow shade.
Handmade jewelry made of silver and semi-precious stones. Inspired by Angelina.
In stock
-
5000 watt / 24V Pure sine inverter-ANEJ1 5000 WATT/ 24v Inverter with digital display
630.00 €
495.00 € Excluding VAT
613.80 € Includes VAT5000 watt / 24V Pure sine inverter-ANEJ1 5000 WATT/ 24v Inverter with digital display
-
European Photovoltaic standalone up to 24kwh 48V + 2V 507ah + Victron Multiplus 5000VA for permanent residences
8,900.00 €
7,582.00 € Excluding VAT
9,401.68 € Includes VATEuropean Photovoltaic standalone up to 24kwh 48V + 2V 507ah + Victron Multiplus 5000VA for permanent residences
Available on backorder
-
2V ECOPVSM 400 Deep Discharge Battery, Open type
173.00 €
116.00 € Excluding VAT
143.84 € Includes VAT2V ECOPVSM 400 Deep Discharge Battery, Open type
The 2V ECOPVSM 400 Deep Charging Battery, open type is an economical and reliable solution for energy storage from small and medium autonomous PV systems. The maximum life time according to the specifications of the manufacturer is 15 years (Design Life under Float Conditions) while it has very high quality characteristics in relation to the most expensive corresponding type and capacity batteries on the market.
Capacity: 395Ah / C-100
Dimensions: 198mm x 83mm x 478mm
Weight: 18,6 Kgr
Price without VAT.
Minimum order 6 pieces
Available on backorder
-
Sunware SW 3065
700.00 €
565.00 € Excluding VAT
700.60 € Includes VATGermany 48Wp Monocrystalline silicon panel with stainless steel frame
Seawater resistance suitable for yachts, yachts, caravansPrice without VAT
In stock
-
Wind turbine X600Watt - 700Watt
1,550.00 €
999.00 € Excluding VAT
1,238.76 € Includes VAT600-700watt / 24v European standards, low noise, low start 2 M / S and high efficiency. Very sturdy construction with the possibility for Marine Use.
It produces energy 3.5-4KWh, with wind 5,5-6.5 Beaufort and for 5-6 hours per 24 hours of wind potential. It has a special type of advanced technology digital charge controller (Controller) with deflection load. This type of regulator is clearly of a higher standard and durability than wind turbines with a built-in controller.
Price without VAT
